|
|
PDF PI4IOE5V9522 Data sheet ( Hoja de datos )
| Número de pieza | PI4IOE5V9522 | |
| Descripción | 4-bit I2C-bus and SMBus low power I/O port | |
| Fabricantes | Pericom Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PI4IOE5V9522 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
PI4IOE5V9522
4-bit I2C-bus and SMBus low power I/O port with interrupt and reset
Features
Operation power supply voltage from 2.3V to 5.5V
4-bit I2C-bus GPIO with interrupt and reset
5V tolerant I/Os
Active Low interrupt output
Active Low reset input
Polarity inversion register
Low current consumption
0Hz to 1MHz clock frequency
Noise filter on SCL/SDA inputs
Power-on reset
ESD protection (4KV HBM and 1KV CDM)
Package offered:MSOP-10L
Pin Configuration
Description
The PI4IOE5V9522 provides 4 bits of General
Purpose parallel Input/Output (GPIO) expansion for
I2C-bus/ SMBus applications. It includes the features
such as higher driving capability, 5V tolerance, lower
power supply, individual I/O configuration, and
smaller packaging. It provides a simple solution when
additional I/O is needed for ACPI power switches,
sensors, push buttons, LEDs, fans, etc.
The PI4IOE5V9522 consists of a 4-bit register to
configure the I/Os as either inputs or outputs, and a 4-
bit polarity registers to change the polarity of the input
port register data. The data for each input or output is
kept in the corresponding Input port or Output port
register. All registers can be read by the system master.
The PI4IOE5V9522 open-drain interrupt output
(INT) is activated when any input state and is used to
indicate the system master that an input state has
changed.
The power-on reset sets the registers to their
default values and initializes the device state machine.
The Reset pin causes the same reset/initialization to
occur without de-powering the device.
Figure1 :MSOP-10
2016-01-0027
PT0556-1
02/15/16
1
1 page  
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Dynamic Characteristics
Table 3: Dynamic characteristics
Symbol
Parameter
fSCL
tBUF
tHD;STA
tSU;STA
tSU;STO
tVD;ACK[1]
tHD;DAT[2]
SCL clock frequency
bus free time between a STOP
and START condition
hold time (repeated) START
condition
set-up time for a repeated
START condition
set-up time for STOP condition
data valid acknowledge time
data hold time
tVD;DAT data valid time
tSU;DAT data set-up time
tLOW LOW period of the SCL clock
tHIGH HIGH period of the SCL clock
tf
fall time of both SDA and SCL
signals
tr
rise time of both SDA and SCL
signals
pulse width of spikes that must
tSP be
suppressed by the input filter
Port timing
tv(Q) Data output valid time[3]
tsu(D) Data input set-up time
th(D) Data input hold time
Interrupt timing
tv(INT)
Valid time on pin INT
trst(INT)
Reset time on pin INT
PI4IOE5V9522
4-bit I2C-bus and SMBus
low power I/O port with interrupt and reset
|||||||||||||||||
Test
Conditions
Standard
mode I2C
Min Max
Fast mode
I2C
Min Max
Fast mode
Plus I2C
Min Max
Unit
0 100 0 400 0 1000 kHz
4.7 - 1.3 - 0.5 - μs
4.0 - 0.6 - 0.26 -
μs
4.7 - 0.6 - 0.26 -
μs
4.0 - 0.6 - 0.26 -
μs
- 3.45 - 0.9 - 0.45 μs
0 - 0 - 0 - ns
- 3.45 - 0.9 - 0.45 us
250 -
4.7 -
4.0 -
100 - 50 -
1.3 - 0.5 -
0.6 - 0.26 -
ns
μs
μs
- 300 - 300 - 120 ns
- 1000 - 300 - 120 ns
- 50 - 50
50 ns
- 200 - 200 - 200
100 - 100 - 100 -
1-1-1 -
ns
ns
μs
- 4 - 4 - 4 μs
- 4 - 4 - 4 μs
2016-01-0027
PT0556-1
02/15/16
5
5 Page 
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Figure 8: Read Input port register
PI4IOE5V9522
4-bit I2C-bus and SMBus
low power I/O port with interrupt and reset
|||||||||||||||||
Note: Transfer of data can be stopped at any moment by a STOP condition. It is assumed that the command byte has previously been set to ‘00’ (read
Input Port register).
Application design-in information
Figure 9: Typical application
IO0 configured as outputs.
IO1, IO2, IO3 configured as inputs.
2016-01-0027
11
PT0556-1
02/15/16
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet PI4IOE5V9522.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PI4IOE5V9521 | 2-bit I2C-bus and SMBus low power I/O port | Pericom Semiconductor |
| PI4IOE5V9522 | 4-bit I2C-bus and SMBus low power I/O port | Pericom Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |