|
|
PDF MTP2N60E Data sheet ( Hoja de datos )
| Número de pieza | MTP2N60E | |
| Descripción | Power Field Effect Transistor | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MTP2N60E (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
MTP2N60E
Designer’s™ Data Sheet
TMOS E−FET.™
Power Field Effect
Transistor
N−Channel Enhancement−Mode Silicon
Gate
This high voltage MOSFET uses an advanced termination scheme
to provide enhanced voltage−blocking capability without degrading
performance over time. In addition, this advanced TMOS E−FET is
designed to withstand high energy in the avalanche and commutation
modes. The new energy efficient design also offers a drain−to−source
diode with a fast recovery time. Designed for high voltage, high speed
switching applications in power supplies, converters and PWM motor
controls, these devices are particularly well suited for bridge circuits
where diode speed and commutating safe operating areas are critical
and offer additional safety margin against unexpected voltage
transients.
• Robust High Voltage Termination
• Avalanche Energy Specified
• Source−to−Drain Diode Recovery Time Comparable to a Discrete
Fast Recovery Diode
• Diode is Characterized for Use in Bridge Circuits
• IDSS and VDS(on) Specified at Elevated Temperature
http://onsemi.com
TMOS POWER FET
2.0 AMPERES, 600 VOLTS
RDS(on) = 3.8 W
TO−220AB
CASE 221A−06
Style 5
D
®G
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Rating
Symbol
Value
S
Unit
Drain−to−Source Voltage
Drain−to−Gate Voltage (RGS = 1.0 MΩ)
Gate−to−Source Voltage — Continuous
— Single Pulse (tp ≤ 50 μs)
Drain Current — Continuous
— Single Pulse (tp ≤ 10 μs)
VDSS
VDGR
VGS
ID
IDM
600 Vdc
600 Vdc
± 20 Vdc
± 40
2.0 Adc
9.0
Total Power Dissipation
Derate above 25°C
PD 50 Watts
0.4 W/°C
Operating and Storage Temperature Range
Single Pulse Drain−to−Source Avalanche Energy — Starting TJ = 25°C
(VDD = 50 Vdc, VGS = 10 Vdc, L = 95 mH, RG = 25 Ω, Peak IL = 2.0 Adc)
TJ, Tstg
EAS
−55 to 150
190
°C
mJ
Thermal Resistance — Junction to Case°
— Junction to Ambient°
RθJC
RθJA
2.5°
62.5°
°C/W
Maximum Lead Temperature for Soldering Purposes, 1/8″ from case for 10 seconds
TL 260 °C
Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit
curves — representing boundaries on device characteristics — are given to facilitate “worst case” design.
Preferred devices are Motorola recommended choices for future use and best overall value.
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 3
1
Publication Order Number:
MTP2N60E/D
1 page  
MTP2N60E
15
12 VDS
TJ = 25°C
ID = 2 A
500
400
9 QT
6 Q1
Q2
3
VGS
Q3
00 4
8
VDS = 100 V
VDS = 250 V
VDS = 400 V
300
200
100
0
12 16 20
QG, TOTAL GATE CHARGE (nC)
Figure 8. Gate−To−Source and Drain−To−Source
Voltage versus Total Charge
1000 TJ = 25°C
ID = 2 A
VDS = 300 V
VGS = 10 V
100
10
td(off)
tf
tr
td(on)
1
1 10 100 10
RG, GATE RESISTANCE (OHMS)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN−TO−SOURCE DIODE CHARACTERISTICS
2.0
1.8
VGS = 0 V
TJ = 25°C
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85
VSD, SOURCE−TO−DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain−to−source voltage and
drain current that a transistor can handle safely when it is
forward biased. Curves are based upon maximum peak
junction temperature and a case temperature (TC) of 25°C.
Peak repetitive pulsed power limits are determined by using
the thermal response data in conjunction with the
procedures discussed in AN569, “Transient Thermal
Resistance−General Data and Its Use.”
Switching between the off−state and the on−state may
traverse any load line provided neither rated peak current
(IDM) nor rated voltage (VDSS) is exceeded and the
transition time (tr,tf) do not exceed 10 μs. In addition the
total power averaged over a complete switching cycle must
not exceed (TJ(MAX) − TC)/(RθJC).
A Power MOSFET designated E−FET can be safely used
in switching circuits with unclamped inductive loads. For
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and adjusted for operating conditions
differing from those specified. Although industry practice is
to rate in terms of energy, avalanche energy capability is not
a constant. The energy rating decreases non−linearly with
an increase of peak current in avalanche and peak junction
temperature.
Although many E−FETs can withstand the stress of
drain−to−source avalanche at currents up to rated pulsed
current (IDM), the energy rating is specified at rated
continuous current (ID), in accordance with industry custom.
The energy rating must be derated for temperature as
shown in the accompanying graph (Figure 12). Maximum
energy at currents below rated continuous ID can safely be
assumed to equal the values indicated.
http://onsemi.com
5
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet MTP2N60E.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MTP2N60E | TMOS POWER FET |  Motorola Semiconductors |
| MTP2N60E | Trans MOSFET N-CH 600V 2A 3-Pin(3+Tab) TO-220 |  New Jersey Semiconductor |
| MTP2N60E | Power Field Effect Transistor | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |