|
|
Número de pieza | BTS5682E | |
Descripción | SPI Power Controller | |
Fabricantes | Infineon Technologies | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de BTS5682E (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! Data Sheet, Rev. 1.0, Jan. 2008
SPOC - BTS5682E
SPI Power Controller
Automotive Power
1 page 2 Block Diagram
SPOC - BTS5682E
Block Diagram
VDD
IN0
IN1
IN2
IN3
IN4
IN5
IS
LH I
CS
SC LK
SO
SI
pow er
s upply
ESD
prot ec t ion
driv er
logic
tem perature
sensor
gate control
&
charge pum p
load current
sense
clam p for
induc t iv e
load
load current
lim itation
channel
01
23
45
current sense m ultiplexer
lim p hom e control
sw itch bypass
m onitor
PW M control
SPI
GND
Figure 1 Block Diagram SPOC - BTS5682E
VBB
OUT5
OUT4
OUT3
OUT2
OUT1
OUT0
Data Sheet
5 Rev. 1.0, 2008-01-22
5 Page SPOC - BTS5682E
Power Supply
5 Power Supply
The SPOC - BTS5682E is supplied by two supply voltages VBB and VDD. The VBB supply line is used by the power
switches. The VDD supply line is used by the SPI related circuitry and for driving the SO line. A capacitor between
pins VDD and GND is recommended as shown in Figure 23.
There is a power-on reset function implemented for the VDD logic power supply. After start-up of the logic power
supply, all SPI registers are reset to their default values. The SPI interface including daisy chain function is active
as soon as VDD is provided in the specified range independent of VBB. The first SPI transmission after a reset
contains at pin SO the read information from register OUT, the transmission error bit TER is set.
5.1 Power Supply Modes
The following table shows all possible power supply modes for VBB, VDD and the pin LHI.
Power Supply Modes Off Off SPI on Reset
VBB 0 V 0 V 0 V 0 V
VDD 0 V 0 V 5 V 5 V
LHI 0 V 5 V 0 V 5 V
PROFET operating
–
–
–
–
Limp home
––––
SPI (logic)
– – ✓ reset
Stand-by current
––––
Idle current
––––
Diagnosis
––––
1) SPI read only.
2) Depending on latched channel 5.
3) When DCR.MUX = 111b and channel 5 in OFF-state.
4) When all channels are in OFF-state and DCR.MUX!= 111b.
5) Current sense disabled in limp home mode.
Off 2)
13.5 V
0V
0V
✓2)
–
reset
✓2)
–
–
Limp Home
mode
without SPI
13.5 V
0V
5V
✓
✓
reset
–
–
–
Normal
operation
13.5 V
5V
0V
✓
–
✓
✓3)
✓4)
✓
Limp Home
mode with
SPI 1)
13.5 V
5V
5V
✓
✓
reset
–
–
✓5)
Stand-by mode is entered as soon as the current sense multiplexer (DCR.MUX) is in default (stand-by) position
and channel 5 is not latched in ON-state1). Additionally, all thermal latches are cleared automatically. As soon as
stand-by mode is entered, register HWCR.STB is set. The state of channel 5 can be read via HWCR.CH5. To wake-
up the device, the current sense multiplexer (DCR.MUX) is programmed different to default (stand-by) position.
Idle mode parameters are valid, when all channels are switched off, but the current sense multiplexer is not in
default position, and VDD supply is available.
Limp home (LHI = high) will wake-up the device and is working without VDD supply. As a result, all channels can
be activated via the dedicated input pins. The cranking latch is not available in limp home mode in order to switch
to stand-by mode after limp home.
1) Not affected by the inputs state
Data Sheet
11
Rev. 1.0, 2008-01-22
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet BTS5682E.PDF ] |
Número de pieza | Descripción | Fabricantes |
BTS5682E | SPI Power Controller | Infineon Technologies |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |