|
|
Número de pieza | LQ255T3LZ48 | |
Descripción | TFT-LCD Module | |
Fabricantes | Sharp Electrionic | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LQ255T3LZ48 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! 1 page LD- 18328-2
4. Input Terminals
4-1. TFT panel driving
CN1 (Interface signals and +5V DC power supply) (Shown in Fig.1)
Using connector FI-X30SSL-HF (Japan Aviation Electronics Ind. , Ltd.) or equivalent
Mating connector FI-X30H/FI-X30HL, FI-X30C/FI-X30C2L
or FI-X30M (Japan Aviation Electronics Ind. , Ltd.)
Mating LVDS transmitter THC63LVDM83A or equivalent device
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Symbol
VCC
VCC
VCC
VCC
GND
GND
GND
GND
SELLVDS
NC
GND
RIN0-
RIN0+
GND
RIN1-
RIN1+
GND
RIN2-
RIN2+
GND
CLKIN-
CLKIN+
GND
RIN3-
RIN3+
GND
R/L
Function
+5V Power Supply
+5V Power Supply
+5V Power Supply
+5V Power Supply
GND
GND
GND
GND
Select LVDS data order Note 1
Ground
Negative (-) LVDS differential data input
Positive (+) LVDS differential data input
Ground
Negative (-) LVDS differential data input
Positive (+) LVDS differential data input
Ground
Negative (-) LVDS differential data input
Positive (+) LVDS differential data input
Ground
Clock Signal(-)
Clock Signal(+)
Ground
Negative (-) LVDS differential data input
Positive (+) LVDS differential data input
Ground
Horizontal shift direction Note 2
28 U/D Vertical shift direction Note 2
29
Reserved
Not Available
30
Reserved
Not Available
Remark
Pull up
Default H:3.3V
Note 3
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
Pull down
Default L:GND
Note 4
Pull down
Default L:GND
Note 4
note GND of a liquid crystal panel drive part has connected with a module chassis.
5 Page 4-2. Backlight driving
CN3 (Inverter control)
Using connector: B14B-PH-SM3-TB(JST)
Mating connector: PHR-14 (JST)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Symbol
VINV
VINV
VINV
VINV
VINV
GND
GND
GND
GND
GND
Reserved
VON
VBRT
Reserved
Function
+24V
+24V
+24V
+24V
+24V
GND
GND
GND
GND
GND
NC
Inverter ON/OFF
Brightness Control
NC
Remark
Note 1
Note 2
LD- 18328-8
Note 1 Inverter ON/OFF
Input voltage
5V
0V
Function
Inverter: ON
Inverter: OFF
Note 2 Brightness Control
PWM Brightness Control is regulated by analog input voltage (0V to 3.3V) .
Input voltage
0V
3.3V
Function
Brightness Control : (Dark)
Brightness Control : (Bright)
4-3. The back light system characteristics
The back light system is direct type with 7 CCFTs (Cold Cathode Fluorescent Tube).
The characteristics of the lamp are shown in the following table.
The value mentioned below is at the case of one CCFT.
Item Symbol Min.
Typ.
Max.
Unit Remarks
Life time
TL
60000
-
-
Hour
Note
Note Lamp life time is defined as the time when brightness becomes 50% of the original value in the
continuous operation under the condition of Ta=25 and brightness control(VBRT=3.3V).
This definition is valid with the condition that the module is placed horizontally. (The wide side of the
module should be parallel to the ground.)
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet LQ255T3LZ48.PDF ] |
Número de pieza | Descripción | Fabricantes |
LQ255T3LZ44 | TFT-LCD Module | Sharp Electrionic |
LQ255T3LZ44A | TFT-LCD Module | Sharp Electrionic |
LQ255T3LZ48 | TFT-LCD Module | Sharp Electrionic |
LQ255T3LZ49 | TFT-LCD Module | Sharp Electrionic |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |