|
|
Número de pieza | BTM-860 | |
Descripción | Class2 Stereo Flash Module | |
Fabricantes | ETC | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de BTM-860 (archivo pdf) en la parte inferior de esta página. Total 18 Páginas | ||
No Preview Available ! Rayson Bluetooth ® Module
CSR8670 Class2 Stereo Flash Module BTM-860
Features
The module is a Max.4dBm( Class2 ) module.
Fully Qualified Bluetooth v4.0.
Integrated Switched-Mode Regulator.
Integrated Battery Charger (200mA)
16Mb internal flash memory (64-bit wide,45ns)
Serial Quad I/O Flash_4Mb(Option)
Embedded Kalimba DSP Co-Processor.
Integrated 16-bit Stereo Audio CODEC.
Support for CSR’s latest CVC technology for narrowband
and wideband voice connections including wind
noise reduction.
Support Host Interface: USB2.0 or UART.
Audio interfaces: I²S, PCM and SPDIF
SBC, MP3, AAC, Faststream ,APTX codec support.
APTX low-latency including support for SCMS-T
HSP / HFP / A2DP / AVRCP/ PBAP / SPP
Bluetooth Low Energy compatible
Support for up to 6 capacitive touch sensor inputs
Integrated chip antenna
RoHS compliant.
Small outline. 16.0 x 23.9 x 2.3 mm
Outline
Applications
Stereo Wireless Headsets.
Wired or wireless speakers and headphones.
Smart remote controllers.
TVs
Audio adaptors
General Electrical Specification
Absolute Maximum Ratings:
Ratings
Storage Temperature
Supply Voltage (VCHG)
Supply Voltage (VBAT)
Supply Voltage (VBAT_SENSE)
Supply Voltage (VREG_ENABLE)
Min.
-40 ℃
-0.4V
-0.4V
-0.4V
-0.4V
V05 2013.11.04
Max.
+85 ℃
5.75V
4.4V
5.75V
4.4V
1 page Digital
Digital Terminals
Input Voltage
VIL input logic level low
VIH input logic level high
Tr/Tf
Output Voltage
VOL output logic level low, IOL = 4.0mA
VIH output logic level high, IOH = -0.4mA
Tr/Tf
Input and Tristate Currents
Strong pull-up
Strong pull-down
Weak pull-up
Weak pull-down
CI input Capacitance
Min
Typ
Max
Unit
-0.4
0.7xPIO_POWER
-
- 0.4 V
- PIO_POWER+0.4 V
- 25 ns
-
0.75xPIO_POWER
-
-
-
-
0.4 V
-V
5 ns
-150
10
-5
0.33
1.0
-40 -10 uA
40 150 uA
-1.0 -0.33 uA
1.0 5.0 uA
5.0 pF
LED Driver Pads
LED Driver Pads
Current, IPAD
LED pad voltage, VPAD
LED pad resistance
VOL output logic level low(a)
VOH output logic level high(a)
VIL input logic level low
VIH input logic level high
High impedance state
Current sink state
IPAD = 10mA
VPAD < 0.5V
(a) LED output port is open-drain and requires a pull-up
Min
Typ
Max
Unit
- - 5 μA
- - 10 mA
- - 0.55 V
- - 40 Ω
- 0 -V
- 0.8 - V
- 0 -V
- 0.8 - V
Auxiliary ADC
Auxiliary ADC
Resolution
Input voltage range(a)
Accuracy
(Guaranteed monotonic)
Offset
Gain error
Input bandwidth
Conversion time
Sample rate(b)
INL
DNL
Min
-
0
-1
0
-1
-0.8
-
1.38
-
Typ
-
-
-
-
-
-
100
1.69
-
Max
10
1.35
1
1
1
0.8
-
2.75
700
Unit
Bits
V
LSB
LSB
LSB
%
kHz
μs
Samples/s
5 Page 1. Serial Interface
1.1 USB Interface
BTM-860 has a full-speed (12Mbps) USB interface for communicating with other compatible digital devices.
The USB interface on BTM-860 acts as a USB peripheral, responding to requests from a master host controller.
BTM-860 contains internal USB termination resistors and requires no external resistor matching.
BTM-860 supports the Universal Serial Bus Specification, Revision v2.0 (USB v2.0 Specification), supports
USB standard charger detection and fully supports the USB Battery Charging Specification , available from
http://www.usb.org. For more information on how to integrate the USB interface on BTM-860 see the Bluetooth and
USB Design Considerations Application Note.
As well as describing USB basics and architecture, the application note describes:
■ Power distribution for high and low bus-powered configurations
■ Power distribution for self-powered configuration, which includes USB VBUS monitoring
■ USB enumeration
■ Electrical design guidelines for the power supply and data lines, as well as PCB tracks and the effects of
ferrite beads
■ USB suspend modes and Bluetooth low-power modes:
- Global suspend
- Selective suspend, includes remote wake
- Wake on Bluetooth, includes permitted devices and set-up prior to selective suspend
- Suspend mode current draw
- PIO status in suspend mode
- Resume, detach and wake PIOs
■ Battery charging from USB, which describes dead battery provision, charge currents, charging in suspend
modes and USB VBUS voltage consideration
■ USB termination when interface is not in use
■ Internal modules, certification and non-specification compliant operation
1.2 Programming and Debug Interface
BTM-860 provides a debug SPI interface for programming, configuring (PS Keys) and debugging the BTM-860.
Access to this interface is required in production. Ensure the 4 SPI signals and the SPI line are brought out to either
test points or a header. To use the SPI interface, the SPI line requires the option of being pulled high externally.
2. interfaces
2.1 Analogue I/O Ports, AIO
BTM-860 has 2 general-purpose analogue interface pin, AIO[0] & AIO[1]. Typically, this connects to a thermistor for
battery pack temperature measurements during charge control.
2.2 LED Drivers
BTM-860 includes a 3-pad synchronised PWM LED driver for driving RGB LEDs for producing a wide range
of colours. All LEDs are controlled by firmware.
11 Page |
Páginas | Total 18 Páginas | |
PDF Descargar | [ Datasheet BTM-860.PDF ] |
Número de pieza | Descripción | Fabricantes |
BTM-860 | Class2 Stereo Flash Module | ETC |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |