|
|
PDF SPE0514S56RG Data sheet ( Hoja de datos )
| Número de pieza | SPE0514S56RG | |
| Descripción | 4-Line ESD Protection Array | |
| Fabricantes | SYNC POWER | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SPE0514S56RG (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
SPE0514
4-Line ESD Protection Array
DESCRIPTION
The SPE0514 are designed by TVS array that is to protect
sensitive electronics from damage or latch-up due to ESD.
They are designed for use in applications where board
space is at a premium. SPE0514 will protect up to four
lines, and may be used on lines where the signal polarities
swing above and below ground.
SPE0514 offer desirable characteristics for board level
protection including fast response time, low operating and
clamping voltage, and no device degradation.
SPE0514 may be used to meet the immunity requirements
of IEC 61000-4-2, level 4. The small SOT-563 package
makes them ideal for use in portable electronics such as
cell phones, PDA’s, notebook computers, and digital
cameras.
APPLICATIONS
Cellular Handsets and Accessories
Cordless Phone
PDA
Notebooks and Handhelds
Portable Instrumentation
Digital Cameras
MP3 Player
FEATURES
Transient protection for data lines to
IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact)
IEC 61000-4-4 (EFT) 40A (5/50ns)
Protects four I/O lines
Working voltage: 5V
Low leakage current
Low operating and clamping voltages
PIN CONFIGURATION ( SOT-563 / SC-89 )
PART MARKING
2010/06/23 Ver.5
Page 1
1 page  
SPE0514
4-Line ESD Protection Array
APPLICATION NOTE
Device Connection for Protection of Four Data Lines
SPE0514 is designed to protect up to four data lines. The device is connected as follows:
1. The TVS protection of four I/O lines is achieved by connecting pins 1, 3, 4 and 6 to the data lines. Pin 2 is
connected to ground. The ground connection should be made directly to the ground plane for best results. The
path length is kept as short as possible to reduce the effects of parasitic inductance.
Circuit Board Layout Recommendations for Suppression of ESD
Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are
recommended:
1. Place the TVS near the input terminals or connectors to restrict transient coupling.
2. Minimize the path length between the TVS and the protected line.
3. Minimize all conductive loops including power and ground loops.
4. The ESD transient return path to ground should be kept as short as possible.
5. Never run critical signals near board edges
6. Use ground planes whenever possible.
2010/06/23 Ver.5
Page 5
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet SPE0514S56RG.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SPE0514S56RG | 4-Line ESD Protection Array | SYNC POWER |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |