|
|
Número de pieza | AMIS-39101 | |
Descripción | Octal High-Side Driver | |
Fabricantes | AMI SEMICONDUCTOR | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de AMIS-39101 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
No Preview Available ! AMIS-39101: Octal High-Side Driver with Protection
Data Sheet
1.0 General Description
The AMIS-39101 is a robust high-side driver IC featuring eight independent high current output drive channels along with a number of
integrated fault-protection circuits. This highly integrated product is designed for controlled delivery of power to a large variety of loads
in industrial applications including motors, relays and LED arrays, among others. With all driver output channels in the conducting state,
each channel can source up to 350mA of continuous current (resistive load). In cases where all output drivers are not active, higher
output current per channel can be achieved provided that the thermal limits of the device are not exceeded. Furthermore, in order to
minimize system cost each output driver has built-in fly-back diodes. The device withstands short-circuits to ground and supply,
respectively. It is designed with an array of integrated protection features including over-temperature and over-current detection and
shut down. The integrated charge pump requires only one external capacitor and provides for operation of the critical fault-protection
circuitry even in case of low supply voltages. The device can be interfaced to a variety of microcontrollers via the serial peripheral
interface (SPI) link, in turn allowing for monitoring and controlling the state of each of the output drivers individually. In this case, at the
onset of a potential hazardous situation the drivers are switched off and the diagnostic state of the drivers can be extracted via the SPI
interface. The device also features a power down mode for reduced power consumption and has high built-in electrostatic discharge
(ESD) protection capability for robust operation.
2.0 Key Features
• Eight high-side output drivers
• Up to 830mA continuous current per driver pair (resistive load)
• Charge pump with one external capacitor
• SPI
• Short-circuit protection
• Diagnostic features
• Power-down mode
• Internal thermal shutdown
• 3.3V and 5V microcontroller compliant
• Excellent system ESD
• Automotive compliant
• SO28 package with low Rthja
3.0 Typical Applications
• Actuator control
• LED drivers
• Relays and solenoids
• Industrial process control
• Automotive load management
4.0 Ordering Information
Product Name
AMIS39101AGA
Package
PSOP 300-28 (JEDEC MS-013)
Temperature Range
-40°C…85°C
AMI Semiconductor – November 06 - M-20638-001
www.amis.com
1
http://www.Datasheet4U.com
1 page AMIS-39101: Octal High-Side Driver with Protection
Data Sheet
8.0 Electrical and Environmental Ratings
8.1 Absolute Maximum Ratings
Stress levels above those listed in this paragraph may cause immediate and permanent device failure. It is not recommended that
more than one of these conditions be applied simultaneously.
Table 3: Absolute Maximum Ratings
Symbol
VDDN
Description
Power supply voltage
Min.
GND - 0.3
VS
VS power supply on pins VS1 to VS4, load dump,
Pulse 5b 400ms
GND - 0.3
Iout_ON
Maximum output current OUTx pins(1)
The HS driver is switched on
-3000
Iout_OFF
Maximum output current OUTx pins(1)
The HS driver is switched off
-350
I_OUT_VS Maximum output current VS1, 2, 3, 4 pins
-700
Vcapa1
DC voltage on pin CAPA1
0
Vdig_in
VESD
VESD
Tj
Voltage on digital inputs CLK, PDB, WR, DIN
Pins that connect the application (pins VS1..4 and Out1..8)(2)
All other pins(2)
ESD according charged device model(3)
Junction temperature (T<100 hours)
-0.3
-4
-2
-750
-40
Tmr Ambient temperature under bias
-40
Notes:
(1)
(2)
(3)
The power dissipation of the chip must be limited not to exceed the maximum junction temperature Tj.
According to HBM standard MIL-STD-883 method 3015.7.
According to norm EOS/ESD-STM5.3.1-1999 robotic mode.
Max.
6
35
350
350
3750
VS+16.5
VDDN+0.3
+4
+2
+750
175
85
Unit
V
V
mA
mA
mA
V
V
kV
kV
V
°C
°C
8.2 Thermal Characteristics
Table 4: Thermal Characteristics of the Package
Symbol
Rth(vj-a)
Description
Thermal resistance from junction to ambient in power-SO28 package
Conditions
In free air
Value
145
Unit
K/W
Table 5: Thermal Characteristics of the AMIS-39101 on a PCB
PCB Design
Conductivity Top and Bottom Layer
Two layer (35um) Copper planes according to Figure 4 + 25% copper for the remaining areas
Two layer (35um) Copper planes according to Figure 4 + 0% copper for the remaining areas
Four layer JEDEC: 25% copper coverage
EIA/JESD51-7
One layer JEDEC: 25% copper coverage
EIA/JESD51-3
Note:
(1) These values are for general information purposes only, and will change based on each specific PCB design.
Rthja (1)
24
53
25
46
Unit
K/W
K/W
K/W
K/W
AMI Semiconductor – November 06 - M-20638-001
www.amis.com
5
5 Page AMIS-39101: Octal High-Side Driver with Protection
Data Sheet
Figure 5: Timing for Power-down Recovery
DOUT
DIN
INPUT REGISTER
CMD8 CMD DRIVER CMD1
OUTPUT RE GISTER
DIAG
8 STATE DIAG
DIAG
1
COMMAND REGISTER
CMD8
MEMOCMD
CMD1
CMDx
DIAGNOST IC RE GISTER
DIAG
8
MEMODIAG
DIAG
1
High Side
Driver
DIAGx
OUTx
Figure 6: SPI Block Diagram
AMI Semiconductor – November 06 - M-20638-001
www.amis.com
11
11 Page |
Páginas | Total 15 Páginas | |
PDF Descargar | [ Datasheet AMIS-39101.PDF ] |
Número de pieza | Descripción | Fabricantes |
AMIS-39100 | Octal High Side Driver | AMI SEMICONDUCTOR |
AMIS-39100 | Octal High Side Driver | ON Semiconductor |
AMIS-39101 | Octal High-Side Driver | AMI SEMICONDUCTOR |
AMIS-39101 | Octal High Side Driver | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |