DataSheet.es    


PDF TSL2591 Data sheet ( Hoja de datos )

Número de pieza TSL2591
Descripción high sensitivity light-to-digital converter
Fabricantes ams 
Logotipo ams Logotipo



Hay una vista previa y un enlace de descarga de TSL2591 (archivo pdf) en la parte inferior de esta página.


Total 25 Páginas

No Preview Available ! TSL2591 Hoja de datos, Descripción, Manual

TSL2591
Datasheet - Apr. 2013 - ams163.5
General Description
Figure TSL2591 – 1:
Key Benefits and Features
The TSL2591 is a very-high sensitivity light-to-digital converter
that transforms light intensity into a digital signal output
capable of direct I2C interface. The device combines one
broadband photodiode (visible plus infrared) and one
infrared-responding photodiode on a single CMOS integrated
circuit. Two integrating ADCs convert the photodiode currents
into a digital output that represents the irradiance measured on
each channel. This digital output can be input to a
microprocessor where illuminance (ambient light level) in lux is
derived using an empirical formula to approximate the human
eye response. The TSL2591 supports a traditional level style
interrupt that remains asserted until the firmware clears it.
Benefits
Approximates Human Eye Response
Flexible Operation
Suited for Operation Behind Dark Glass
Low Operating Overhead
Low Power 3.0 μA Sleep State
I2C Fast Mode Compatible Interface
Features
Dual Diode
Programmable Analog Gain and Integration Time
600M:1 Dynamic Range
• Two Internal Interrupt Sources
• Programmable Upper and Lower Thresholds
• One Interrupt Includes Programmable Persistence Filter
User Selectable Sleep Mode
• Data Rates up to 400 kbit/s
• Input Voltage Levels Compatible with 3.0V Bus
Datasheet - Apr. 2013 - ams163.5
TSL2591 – 1
Free Datasheet http://www.datasheet4u.com/

1 page




TSL2591 pdf
Electrical Characteristics
Figure TSL2591 – 7:
Recommended Operating Conditions
All limits are guaranteed. The parameters with min and max
values are guaranteed with production tests or SQC (Statistical
Quality Control) methods.
Symbol
VDD
TA
Parameter
Supply voltage
Operating free-air temperature
Min Typ Max Units
2.7 3 3.6 V
-30 70 ºC
Figure TSL2591 – 8:
Operating Characteristics, VDD=3V, TA=25ºC (unless otherwise noted)
Symbol
Parameter
IDD Supply Current
VOL
INT, SDA output low
voltage
ILEAK
Leakage current, SDA,
SCL, INT pins
VIH
SCL, SDA input high
voltage
VIL
SCL, SDA input low
voltage
Conditions
Active
Sleep state - no I2C activity
3mA sink current
6mA sink current
Min Typ Max Units
275 325
2.3 4
μA
0
0
0.4
0.6
V
-5 5 μA
0.7 VDD
V
0.3 VDD
V
Datasheet - Apr. 2013 - ams163.5
TSL2591 – 5
Free Datasheet http://www.datasheet4u.com/

5 Page





TSL2591 arduino
Command Register
7
CMD
65
TRANSACTION
Fields
CMD
Bits
7
TRANSACTION
6:5
ADDR/SF
4:0
The COMMAND register specifies the address of the target
register for future read and write operations, as well as issues
special function commands.
4321 0
ADDR/SF
Description
Select Command Register. Must write as 1 when addressing
COMMAND register.
Select type of transaction to follow in subsequent data transfers
FIELD VALUE
DESCRIPTION
00 Reserved - Do not use
01 Normal Operation
10 Reserved – Do not use
11 Special Function – See description below
Address field/special function field. Depending on the transaction
type, see above, this field either specifies a special function
command or selects the specific control-status-data register for
subsequent read and write transactions. The field values listed
below apply only to special function commands.
FIELD VALUE
DESCRIPTION
00100
Interrupt set – forces an interrupt
00110
Clears ALS interrupt
00111
Clears ALS and no persist ALS interrupt
01010
Clears no persist ALS interrupt
other
Reserved – Do not write
The interrupt set special function command sets the interrupt bits
in the status register (0x13). For the interrupt to be visible on the
INT pin, one of the interrupt enable bits in the enable register
(0x00) must be asserted.
The interrupt set special function must be cleared with an interrupt
clear special function. The ALS interrupt clear special functions
clear any pending interrupt(s) and are self-clearing.
Datasheet - Apr. 2013 - ams163.5
TSL2591 – 11
Free Datasheet http://www.datasheet4u.com/

11 Page







PáginasTotal 25 Páginas
PDF Descargar[ Datasheet TSL2591.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TSL2591high sensitivity light-to-digital converterams
ams

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar