|
|
Número de pieza | PLC-FP-X | |
Descripción | Programmable Controllers | |
Fabricantes | Panasonic | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de PLC-FP-X (archivo pdf) en la parte inferior de esta página. Total 24 Páginas | ||
No Preview Available ! http://www.DataSheet4U.net/
Strengthened Product Lineup
to Meet Diversified Demands
FP-X Series
Programmable Controllers
01/2008
datasheet pdf - http://www.DataSheet4U.net/
1 page FP-X series
Name and function of each part
Input terminals
Power terminals
Control Unit
(Model: Relay output type AFPX-C30R)
I/O status monitor LED
USB communication port (excluding C14R)
RUN/PROG. mode selection switch
Potentiometer
RS232C tool port
24V DC service power output terminals
C14: 0.15A
C30, C60: 0.4A
(DC powered type has no service power output)
Input terminals
Expansion Unit
(Model: Relay output type AFPX-E16R)http://www.DataSheet4U.net/
Add-on cassette interface cover
Connector for
add-on cassette
Connector for
expansion unit
Connector
for battery
Connector for expansion unit
Output terminals
I/O status monitor LED
Connector for expansion unit
Connector for expansion unit
Output terminals
Add-on Cassette
(Model: Analog input cassette AFPX-AD2)
Connector for double-stacked mounting
* Only the communication cassette can be upper.
Securing hole
* Use the two opposite diagonal holes
for mounting when a communication
cassette is double-stacked.
Input/output terminals or communication signal terminals
01/2008
5datasheet pdf - http://www.DataSheet4U.net/
5 Page FP-X series
Multi-point PID control
High-accuracy PID control is possible by adopting a sophisticated algorithm and floating-point operations.
Higher accuracy is obtained by ultra high-speed computations in a 32µs/loop. For example, a 16-loop control only adds a scan
time of 0.5ms by ensuring minimum impact on the tact time.
The simultaneous multi-point auto-tuning simplifies complex parameter setting.
The high-speed control PI-D*¹ mode and overshoot suppression I-PD*² mode are available for selection according to the intended
application.
By combining with a sequence control, the parameters (Kp, Ti, Td, etc.) can be changed during a PID control execution, thereby
enabling optimum temperature control in each stage including start up, mid-range and convergence. The ability to change the tar-
get value easily enables multi-step temperature control, which was difficult with only temperature controllers. In addition, the
multi-point temperature control enables centralized control of multiple temperature controllers with a single FP-X for unified data
management.
*1 Derivative type
*2 Proportional-derivative type
Modbus-RTU
http://www.DataSheet4U.net/
Multiple temperature
controllers
Easy unification of
data management
FP-X
T/C
T/C
T/C
T/C
T/C
The number can even be increased up to 28 channels by using the
thermocouple input cassette and FP0 thermocouple unit.
2 modes are selectable
Partial optimum control by changing Multi-step control by changing
parameters
the target value
Target
value
PI-D mode
I-PD mode
Time
High-speed PID
control
Target
value
Overshoot suppression
Rapid acceleration
Smooth startup
Time
Target value
Time
01/2008
11datasheet pdf - http://www.DataSheet4U.net/
11 Page |
Páginas | Total 24 Páginas | |
PDF Descargar | [ Datasheet PLC-FP-X.PDF ] |
Número de pieza | Descripción | Fabricantes |
PLC-FP-X | Programmable Controllers | Panasonic |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |