|
|
Número de pieza | TS16GSSD25S-S | |
Descripción | 2.5inch Solid State Disk | |
Fabricantes | Transcend | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de TS16GSSD25S-S (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! TTSS88GGSSSSDD2255SS--SS
TTSS1166GGSSSSDD2255SS--SS//MM
TTSS3322GGSSSSDD2255SS--SS//MM
TTSS6644GGSSSSDD2255SS--SS//MM
TTSS112288GGSSSSDD2255SS--MM
TTSS119922GGSSSSDD2255SS--MM
Description
Due to smaller size (fit the standard dimensions of
2.5” SATA Hard Disk Drives), huge capacity, high
speed, and low power consumption, Solid State Disk
is perfect replacement storage device for PCs,
Laptops, gaming systems, and handheld devices.
Placement
B
C
A
2.5” Solid State Disk
Features
• RoHS compliant
• Fully compatible with devices and OS that support the
SATA 3Gb/s standard
• Non-volatile Flash Memory for outstanding data
retention
• Built-in ECC (Error Correction Code) functionality and
wear-leveling algorithm ensures highly reliable of data
transfer
• Shock resistance
Dimensions
Side
Millimeters
Inches
http://www.DataSheet4U.net/
A
100.30 ± 0.40
3.949 ± 0.016
B
69.85 ± 0.20
2.750 ± 0.008
C
9.50 ± 0.15
0.374 ± 0.004
Transcend Information Inc.
1
V2.4
datasheet pdf - http://www.DataSheet4U.net/
1 page TTSS88GGSSSSDD2255SS--SS
TTSS1166GGSSSSDD2255SS--SS//MM
TTSS3322GGSSSSDD2255SS--SS//MM
TTSS6644GGSSSSDD2255SS--SS//MM
TTSS112288GGSSSSDD2255SS--MM
TTSS119922GGSSSSDD2255SS--MM
2.5” Solid State Disk
Package Dimensions
Below figure illustrates the Transcend 2.5” SATA Solid State Disk. All dimensions are in mm.
http://www.DataSheet4U.net/
*Note: Tighten mounting screws with no more than 1.0Kg-cm (0.07ft-lbs) of torque.
Transcend Information Inc.
5
V2.4
datasheet pdf - http://www.DataSheet4U.net/
5 Page TTSS88GGSSSSDD2255SS--SS
TTSS1166GGSSSSDD2255SS--SS//MM
TTSS3322GGSSSSDD2255SS--SS//MM
TTSS6644GGSSSSDD2255SS--SS//MM
TTSS112288GGSSSSDD2255SS--MM
TTSS119922GGSSSSDD2255SS--MM
2.5” Solid State Disk
Description:
1. Host/device are powered and operating normally with some form of active communication.
2. Some condition in the host causes the host to issue COMRESET
3. Host releases COMRESET. Once the condition causing the COMRESET is released, the host releases the
COMRESET signal and puts the bus in a quiescent condition.
4. Device issues COMINIT – When the device detects the release of COMRESET, it responds with a COMINIT. This is
also the entry point if the device is late starting. The device may initiate communications at any time by issuing a COMINIT.
5. Host calibrates and issues a COMWAKE.
6. Device responds – The device detects the COMWAKE sequence on its RX pair and calibrates its transmitter (optional).
Following calibration the device sends a six burst COMWAKE sequence and then sends a continuous stream of the
ALIGN sequence starting at the device's highest supported speed. After ALIGNP Dwords have been sent
for 54.6us (2048 nominal Gen1 Dword times) without a response from the host as determined by detection of ALIGNP
primitives received from the host, the device assumes that the host cannot communicate at that speed. If additional
speeds are available the device tries the next lower supported speed by sending ALIGNP Dwords at that rate for
http://www.DataSheet4U.net/
54.6 us (2048 nominal Gen1 Dword times.) This step is repeated for as many slower speeds as are supported. Once the
lowest speed has been reached without response from the host, the device enters an error state.
7. Host locks – after detecting the COMWAKE, the host starts transmitting D10.2 characters at its lowest supported rate.
Meanwhile, the host receiver locks to the ALIGN sequence and, when ready, returns the ALIGN sequence to the device at
the same speed as received. A host shall be designed such that it acquires lock in 54.6us (2048
nominal Gen1 Dword times) at any given speed. The host should allow for at least 873.8 us (32768 nominal Gen1 Dword
times) after detecting the release of COMWAKE to receive the first ALIGNP. This ensures interoperability with
multi-generational and synchronous designs. If no ALIGNP is received within 873.8 us (32768 nominal Gen1 Dword
times) the host restarts the power-on sequence – repeating indefinitely until told to stop by the Application layer.
8. Device locks – the device locks to the ALIGN sequence and, when ready, sends SYNCP indicating it is ready to start
normal operation.
9. Upon receipt of three back-to-back non-ALIGNP primitives, the communication link is established and normal operation
may begin.
Transcend Information Inc.
11
V2.4
datasheet pdf - http://www.DataSheet4U.net/
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet TS16GSSD25S-S.PDF ] |
Número de pieza | Descripción | Fabricantes |
TS16GSSD25S-M | 2.5inch Solid State Disk | Transcend |
TS16GSSD25S-S | 2.5inch Solid State Disk | Transcend |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |