|
|
Número de pieza | ITS640S2S | |
Descripción | Smart Sense High-Side Power Switch | |
Fabricantes | Infineon | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ITS640S2S (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
No Preview Available ! PROFET® ITS 640S2
Smart Sense High-Side Power Switch
For Industrial Applications
Features
• Short circuit protection
• Current limitation
• Proportional load current sense
• CMOS compatible input
• Open drain diagnostic output
• Fast demagnetization of inductive loads
• Undervoltage and overvoltage shutdown with
auto-restart and hysteresis
• Overload protection
• Thermal shutdown
• Overvoltage protection including load dump
(with external GND-resistor)
• Reverse battery protection (with external GND-
resistor)
• Loss of ground and loss of Vbb protection
• Electrostatic discharge (ESD) protection
Product Summary
Operating voltage
Vbb(on) 5.0 ... 34 V
On-state resistance RON
30 mΩ
Load current (ISO)
IL(ISO)
12.6 A
Current limitation
IL(SCr)
24 A
Operating temperature Ta -30 … +85 °C
Package
PG-TO220-7-11
PG-TO220-7-12
1
Standard (staggered)
1
Straight
Application
• µC compatible power switch with diagnostic feedback for 12 V and 24 V DC grounded loads in industrial
applications
• All types of resistive, inductive and capacitive loads
• Replaces electromechanical relays, fuses and discrete circuits
General Description
N channel vertical power FET with charge pump, groundh refteretncep d C: MO/ S / comw paw tiblwe in. putD ana d dt iaganosS tic h e e t 4
feedback, proportional sense of load current, monolithically integrated in Smart SIPMOS technology.
Providing embedded protective functions.
Block Diagram
3 IN
Voltage
source
V Logic
Voltage
sensor
1 ST ESD
Logic
Overvoltage
protection
Current
limit
Gate
protection
Charge pump
Level shifter
Rectifier
Limit for
unclamped
ind. loads
Output
Voltage
detection
5 IS
I IS
RIS
GND
2
Signal GND
Temperature
sensor
+ Vbb
4
Current
Sense
OUT 6, 7
IL
Load
RO
GND
PROFET
Load GND
Infineon Technologies AG
Page 1 of 15
2006-Mar-28
dat
1 page Parameter and Conditions
at Tj = 25 °C, Vbb = 12 V unless otherwise specified
Symbol
Protection Functions7)
Initial peak short circuit current limit (pin 4 to 6&7)
Tj =-40°C:
Tj =25°C:
Tj =+150°C:
Repetitive short circuit shutdown current limit
Tj = Tjt (see timing diagrams, page 11)
Output clamp (inductive load switch off)
at VOUT = Vbb - VON(CL); IL= 40 mA,
Tj =-40°C:
Tj =+25..+150°C:
Thermal overload trip temperature
Thermal hysteresis
Reverse battery (pin 4 to 2) 8)
Reverse battery voltage drop (Vout > Vbb)
IL = -5 A
Tj=150 °C:
IL(SCp)
IL(SCr)
VON(CL)
Tjt
∆Tjt
-Vbb
-VON(rev)
Diagnostic Characteristics
Current sense ratio9), static on-condition,
VIS = 0...5 V, Vbb(on) = 6.510)...27V,
kILIS = IL / IIS
Tj = -40°C, IL = 5 A:
Tj= -40°C, IL= 0.5 A:
http://www.DataSheet4U.net/
Tj= 25...+150°C, IL= 5 A:
, Tj= 25...+150°C, IL = 0.5 A:
Current sense output voltage limitation
Tj = -40 ...+150°C
IIS = 0, IL = 5 A:
Current sense leakage/offset current
Tj = -40 ...+150°C
VIN=0, VIS = 0, IL = 0:
VIN=5 V, VIS = 0, IL = 0:
VIN=5 V, VIS = 0, VOUT = 0 (short circuit):
kILIS
VIS(lim)
IIS(LL)
IIS(LH)
IIS(SH)11 )
PROFET® ITS 640S2
Values
Unit
min typ max
48 56
40 50
31 37
-- 24
41 --
43 47
150 --
-- 10
-- --
-- 600
65 A
58
45
-- A
-- V
52
-- °C
-- K
32 V
-- mV
4550
3300
4550
4000
5000
5000
5000
5000
6000
8000
5550
6500
5.4 6.1 6.9 V
0 -- 1 µA
0 -- 15
0 -- 10
7) Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are
not designed for continuous repetitive operation.
8) Requires 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Note that the power dissipation is higher compared to normal
operating conditions due to the voltage drop across the intrinsic drain-source diode. The temperature
protection is not active during reverse current operation! Input and Status currents have to be limited (see
max. ratings page 2 and circuit page 8).
9) This range for the current sense ratio refers to all devices. The accuracy of the kILIS can be raised at least by
a factor of two by matching the value of kILIS for every single device.
In the case of current limitation the sense current IIS is zero and the diagnostic feedback potential VST is
High. See figure 2b, page 10.
10) Valid if Vbb(u rst) was exceeded before.
11) not subject to production test, specified by design
Infineon Technologies AG
Page 5
2006-Mar-28
datasheet pdf - http://www.DataSheet4U.net/
5 Page Figure 2c: Switching an inductive load:
IN
ST
VOUT
PROFET® ITS 640S2
Figure 4a: Overtemperature:
Reset if Tj <Tjt
IN
ST
IL
IL IIS
IIS TJ
t
Figure 3a: Short circuit:
shut down by overtempertature, reset by cooling
IN
Figure 5a: Open load: detection in ON-state,
http://www.DataSheet4U.net/
open load occurs in on-state
t
IL IL(SCp)
IL(SCr)
IN
ST
IIS
ST
t
Heating up may require several milliseconds, depending on
external conditions
IL(SCp) = 50 A typ. increases with decreasing temperature.
VOUT
IL
normal
open normal
IIS t
Infineon Technologies AG
Page 11
2006-Mar-28
datasheet pdf - http://www.DataSheet4U.net/
11 Page |
Páginas | Total 14 Páginas | |
PDF Descargar | [ Datasheet ITS640S2S.PDF ] |
Número de pieza | Descripción | Fabricantes |
ITS640S2 | Smart Sense High-Side Power Switch | Infineon |
ITS640S2S | Smart Sense High-Side Power Switch | Infineon |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |