|
|
PDF TP17LT Data sheet ( Hoja de datos )
| Número de pieza | TP17LT | |
| Descripción | COLOR MONITOR | |
| Fabricantes | Samsung | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TP17LT (archivo pdf) en la parte inferior de esta página. Total 70 Páginas | ||
|
No Preview Available !
COLOR MONITOR
TP17LT
SERVICE Manual
COLOR MONITOR
CONTENTS
1. Precautions
www.DataSheet.co.kr
2. Product Specifications
3. Disassembly & Reassembly
4. Alignment & Adjustments
5. Troubleshooting
6. Exploded View & Parts List
7. Electrical Parts List
8. Block Diagram
9. Wiring Diagram
10. Schematic Diagrams
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
2 Product Specifications
2-1 Specifications
Item Description
Picture Tube:
17-Inch (43 cm): 16-inch (40.6 cm) viewable,
Full-square flat-face tube, 90˚ Deflection, Silica coated with anti-electronic properties
(TCO: Multilayer coating)
Medium-short persistence phosphor, 0.24 mm (H) / 0.14 mm (V) Dot pitch
Scanning Frequency
Horizontal : 30 kHz to 70 kHz (Automatic)
Vertical : 50 Hz to 160 Hz (Automatic)
Display Colors
Unlimited colors
Maximum Resolution
Horizontal : 1280 Dots
Vertical : 1024 Lines
Input Video Signal
Analog, 0.7 Vp-p positive at 75 Ω, internally terminated
Input Sync Signal
Separate Sync: TTL level positive/negative
Maximum Pixel Clock rate
110 MHz
Active Display
Horizontal : 306 mm ± 4 mm / Vertical : 230.5 mm ± 4 mm
Input Voltage
AC 90 to 264 Volts, 60 Hz or 50 Hz ± 3 Hz
Power Consumption
90 Watt (max)
Dimensions
Weight
Unit (Without Speakers) ;
(With Speakers) ;
Carton ;
16.53 x 16.88 x 15.86 Inches (420 x 429 x 403 mm)
20.19 x 16.88 x 15.86 Inches (513x 429 x 403 mm)
21.02 x 21.73 x 21.02 Inches (534 x 552 x 534 mm)
www.DataSheet.co.kr
Without Speakers : 35.3 lbs (16.0 kg) / With Speakers : 37.5 lbs (17.0kg) / Carton : 44.1 lbs (20.0kg)
Environmental Considerations
Operating Temperature :
Humidity :
Storage Temperature :
Humidity :
32°F to 104°F (0°C to 40°C)
10 % to 80 %
-4°F to 113°F (-20°C to 45°C)
5 % to 95 %
• Above model comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields.
• Designs and specifications are subject to change without prior notice.
TP17LT
2-1
Datasheet pdf - http://www.DataSheet4U.net/
5 Page 
4 Alignment and Adjustments
This section of the service manual explains how to make permanent adjustments to the monitor. Directions
are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig).
4-1 Adjustment Conditions
Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the
settings are not permanently stored and may be inadvertently deleted by the user.
4-1-1 Before Making Adjustments
.4-1-2 Required Equipment
4-1-1 (a) ORIENTATION
When servicing, always face the monitor to the
east.
4-1-1 (b) MAGNETIC FIELDS
Whenever possible, use magnetic field isolation
equipment such as a Helmholtz field to surround
the monitor. If a Helmholtz field is not available,
frequently degauss the unit under test.
Caution: Other electrical equipment may cause
external magnetic fields which may
interfere with monitor performance.
Use an external degaussing coil to limit magnetic
build up on the monitor. If an external degaussing
coil is not available, use the internal degaussing
circuit. However, do not use the internal
degaussing circuit more than once per 30 minutes.
4-1-1 (c) WARM-UP TIME
The monitor must be on for 30 minutes before
starting alignment. Warm-up time is especially
critical in color temperature and white balance
adjustments.
4-1-1 (d) SIGNAL
Analog, 0.7 Vp-p positive at 75 ohm, internal
termination
Sync: Separate
(TTL level negative/positive)
4-1-1 (e) SCANNING FREQUENCY
Horizontal: 30 kHz to 70 kHz (Automatic)
Vertical: 50 Hz to 160 Hz (Automatic)
Unless otherwise specified, adjust at the
1024 x 768 mode (68 kHz/85 Hz) signals.
Refer to Table 2-1 on page 2-3.
The following equipment may be necessary for
adjustment procedures:
4-1-2 (a) DISPLAY CONTROL ADJUSTMENT
1. Non-metallic (–) screwdriver:
1.5, 2.5, 3 mm
2. Non-metallic (+) screwdriver:
1.5, 2.5, 3 mm
3. Digital Multimeter (DMM), or
Digital Voltmeter
4. Signal generator, or
DM200 software
5. Software: Softjig or DM200
6. Interface Board Ver. 2.0 Code No.
BH81-90001K
www.DataSheet.co.kr
7.
Parallel communications cable (25-pin to
25-pin); Code No. BH81-90001H
8. Signal cable (15-pin to 15-pin cable with
additional 3-pin connector); Code No.
BH81-90001J
9. 5 V DC adapter, not supplied
10. Personal computer
Note: Softjig Ass’y (includes items 6, 7 and 9)
Code No. BH81-90001L
4-1-2 (b) COLOR ADJUSTMENTS
1. All equipment listed in 4-1-2 (a), above
2. Color analyzer, or any luminance
measurement equipment
TP17LT
4-1
Datasheet pdf - http://www.DataSheet4U.net/
11 Page | ||
| Páginas | Total 70 Páginas | |
| PDF Descargar | [ Datasheet TP17LT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TP17LT | COLOR MONITOR | Samsung |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |