|
|
PDF TSOP35D26 Data sheet ( Hoja de datos )
| Número de pieza | TSOP35D26 | |
| Descripción | IR Receiver Modules | |
| Fabricantes | Vishay Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TSOP35D26 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
www.vishay.com
TSOP35D26
Vishay Semiconductors
IR Receiver Modules for 3D Synchronization Signals
4
3
2
1
16797
MECHANICAL DATA
Pinning:
1 = GND, 2 = N.C., 3 = VS, 4 = OUT
FEATURES
• Compliant to CEA-2038 for long command
encoding
• Command driven IR synchronized active
eyewear standard
• Center frequency at 26.2 kHz to reduce
interference with IR remote control signals at
30 kHz to 56 kHz
• Package can be used with IR emitters with
wavelength 830 nm as well as standard 940 nm
• Very low supply current and stand-by mode
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage range: 2.5 V to 5.5 V
• Improved immunity against modulated light sources
• Insensitive to supply voltage ripple and noise
• Taping available for topview and sideview assembly
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
DESCRIPTION
The TSOP35D26 is an SMD IR receiver module for 3D
synchronization signals. The receiver is designed to operate
at a carrier frequency of 26.2 kHz and a wavelength of 830
www.DataSheet.co.kr
nm to avoid interference with standard remote control
systems at 940 nm and 30 kHz to 56 kHz. The TSOP35D26
can receive continuously transmitted signal patterns with a
minimum burst length of 6 cycles and frame rates up to
200 Hz. The circuit provides good suppression of optical
noise from CFLs, LCD backlight and plasma panels.
PARTS TABLE
CARRIER FREQUENCY
26.2 kHz
BLOCK DIAGRAM
Input
AGC
Band
pass
30 kΩ
Demo -
dulator
PIN
16839
Control circuit
GOOD NOISE SUPPRESSION AND FAST BURST RATE
TSOP35D26
3
VS
4
OUT
1; 2
GND
APPLICATION CIRCUIT
17170_5
Transmitter
with
TSALxxxx
IR receiver
VS
OUT
GND
R1
C1
VO
+ VS
µC
GND
R1 and C1 are recommended for protection against EOS.
Components should be in the range of 33 Ω < R1 < 1 kΩ,
C > 0.1 µF.
1
Rev. 1.2, 12-Mar-12
1 Document Number: 83468
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
www.vishay.com
TSOP35D26
Vishay Semiconductors
Besides conformity to CEA-2038, please note the additional information:
SUITABLE DATA FORMAT
The TSOP35D26 is designed to suppress spurious output
pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 26.2 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the TSOP35D26 in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
• Strongly or weakly modulated noise from fluorescent
lamps with electronic ballasts (see figure 14 or figure 15)
0 5 10 15 20
16920
Time (ms)
Fig. 14 - IR Signal from Fluorescent Lamp
with Low Modulation
Minimum burst length
After each burst of length
a minimum gap time is required of
For bursts greater than
a minimum gap time in the data stream is needed of
Maximum rate of short bursts (constant irradiance)
Maximum rate of short bursts (variable irradiance)
www.DataSheet.co.kr
0
16921
5 10 15
Time (ms)
20
Fig. 15 - IR Signal from Fluorescent Lamp
with High Modulation
TSOP35D26
6 cycles/burst
6 to 24 cycles
≥ 6 cycles
24 cycles
> 4 x burst length
2000 bursts/s
220 bursts/s
Rev. 1.2, 12-Mar-12
5 Document Number: 83468
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet pdf - http://www.DataSheet4U.net/
5 Page 
www.vishay.com
REEL DIMENSIONS in millimeters
TSOP35D26
Vishay Semiconductors
www.DataSheet.co.kr
16734
LEADER AND TRAILER DIMENSIONS in millimeters
Trailer
no devices
devices
Leader
no devices
End
min. 200
COVER TAPE PEEL STRENGTH
According to DIN EN 60286-3
0.1 N to 1.3 N
300 mm/min. ± 10 mm/min.
165° to 180° peel angle
Start
min. 400
96 11818
LABEL
Standard bar code labels for finished goods
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
Rev. 1.2, 12-Mar-12
11 Document Number: 83468
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet pdf - http://www.DataSheet4U.net/
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet TSOP35D26.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TSOP35D25 | IR Receiver Modules |  Vishay Intertechnology |
| TSOP35D26 | IR Receiver Modules | Vishay Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |