|
|
Número de pieza | LV8417CS | |
Descripción | Forward/Reverse Motor Driver | |
Fabricantes | Sanyo Semicon Device | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LV8417CS (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
No Preview Available ! www.DataSheet.co.kr
Ordering number : ENA1996
LV8417CS
Bi-CMOS IC
Forward/Reverse Motor Driver
Overview
The LV8417CS is a 1-channel H bridge motor driver IC. The package size is extremely small with wafer level package
(WLP). Moreover, the on-resistance is low (upper and lower total 0.27Ω typ.).
The application voltage range is wide (2.0V to 10.5V).
The H bridge of this IC is P-N composition and thereby reduces the external parts without need of charge pump.
Therefore, LV8417CS realizes reduction of mounting area which enables lower cost and smaller application size.
Functions
• H-bridge 1-channel forward/reverse motor driver
• IO max=1.0A (t≤100ms 2.0A, t≤10ms 3.8A)
• BiCDMOS process
• Built-in low voltage reset and thermal shutdown circuit
• Output ON resistance (Upper and lower total 0.27Ω; Ts=25°C, IO=1.0A)
Specifications
Maximum Ratings at Ta = 25°C, SGND = PGND = 0V
Parameter
Power supply voltage (for load)
Power supply voltage (for control)
Output current
Output peak current
Input voltage
Allowable power dissipation
Symbol
VM max
VCC max
IO max
IO peak1
IO peak2
VIN max
Pd max
Conditions
t ≤ 100ms
t ≤ 10ms
Mounted on a specified board *
Ratings
-0.5 to 12.6
-0.5 to 6.0
1.0
2.0
3.8
-0.5 to VCC+0.5
850
Unit
V
V
A
A
A
V
mW
Operating temperature
Topr
-20 to +85
°C
Storage temperature
Tstg
-55 to +150
°C
* Specified board : 57mm × 57mm × 1.6mm, glass epoxy both side board.
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high
voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment. The products mentioned herein
shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life,
aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system,
safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives
in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any
guarantee thereof. If you should intend to use our products for new introduction or other application different
from current conditions on the usage of automotive device, communication device, office equipment, industrial
equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the
intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely
responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer's products or
equipment.
D0711 SY 20111012-S00003 No.A1996-1/5
Datasheet pdf - http://www.DataSheet4U.net/
1 page www.DataSheet.co.kr
LV8417CS
Sample Application Circuit
OUT1
Motor connect pin
OUT2
OUT1
PGND
OUT2
VCC
SGND
VM
ENA
IN1
IN2
VCC
(Power pin for control)
SW1
SW2
SW3
VIN
(Power pin for switch)
ENA
IN1
Logic input pin
IN2
VM
(Power pin for loads)
* Connect a kickback absorbing capacitor as close as possible to the IC. Characteristics deterioration of the IC or damage
may result if an instantaneous voltage surge exceeding the maximum rated value is applied to the VM line due to coil
kickback or other causes.
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of December, 2011. Specifications and information herein are subject
to change without notice.
PS No.A1996-5/5
Datasheet pdf - http://www.DataSheet4U.net/
5 Page |
Páginas | Total 5 Páginas | |
PDF Descargar | [ Datasheet LV8417CS.PDF ] |
Número de pieza | Descripción | Fabricantes |
LV8417CS | Forward/Reverse Motor Driver | Sanyo Semicon Device |
LV8417CS | Forward/Reverse Motor Driver | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |