|
|
PDF LXMG221D-0700040-D2F Data sheet ( Hoja de datos )
| Número de pieza | LXMG221D-0700040-D2F | |
| Descripción | 40W 700mA Dimmable HV LED Driver Module | |
| Fabricantes | Microsemi | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LXMG221D-0700040-D2F (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
www.DataSheet.co.kr
LXLMXMG2G220231D-0700040-D2F
TM ® 40W 700mA Dimmable HV LED Driver Module
PRODUCTION DATASHEET
•
DESCRIPTION
KEY FEATURES
The LXMG221D-0700040-D2F is a
fully enclosed compact solid-state LED
lighting driver module. It operates from a
universal AC input supply in the range of
347VAC to 480VAC, 60Hz to drive a string
of LEDs with active power factor
correction. LED string voltage can range
from 40V to 57V at a constant current of
700mA.
Control terminal leads include a
dimming input BRITE A with a dedicated
RETURN lead. The amplitude of the
output LED string current will vary from
10% to 100% corresponding to a 1VDC to
10VDC signal on the BRITE A input
following the 0V to 10V ESTA E1.3-2001
Analog Control Specification Standard.
The BRITE A terminal when pulled down
below minimum dimming will turn off the
LEDs and enter a low power consumption
mode. A second control terminal lead
provides a FAULT indicator.
In the case that there is an LED string
short between OUTPUT(+) and
OUTPUT(-), or string open, or a product
over temperature condition the FAULT
terminal will go low. The FAULT
terminal includes an open collector device
that can be pulled up to a maximum of
60V and will sink 8mA typical to 0.8V
when a short or open fault occurs.
To reduce audible noise the internal
switching frequency remains above
30kHz. Safety features include open
output circuit protection, whole string
short circuit protection. The maximum
allowable hot spot case temperature is
90°C (above this temperature the module
will be thermally self-protected). The
recommended operating ambient
temperature range is -30°C to 70°C, as
long as the maximum case temperature is
not exceeded. The compact enclosure is
rated to IP66, meets UL8750 and UL1310
class 2.
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
Patents Pending
PRODUCT HIGHLIGHT
• High Voltage AC Input: 347VAC to
480VAC
• High Efficiency
• Active Power Factor Correction
• Constant Current 700mA
• Dimming Input Provides 10% to
100% Range, Plus Shutdown
• Anode Supply Adjusts for String
Voltage between 40V and 57V
• Small Compact Size
• Suitable for Damp Locations (IP66)
• UL8750 & UL1310
• UL File E337545
• FCC Class B
• Long Life Expectancy
• RoHS Compliant
• Full Protection: OVP, SCP, OTP,
Maximum Power Limit
• Unique Fault Detection and
Management
•
APPLICATIONS
Residential and Commercial LED
Lighting Fixtures such as:
• LED Down Lights
• LED Street Lights
Part Number
LXMG221D-0700040-D2F
Photo is representative only, actual product may differ slightly
ORDER INFORMATION
Input Voltage
Output Current
347VAC to 480VAC 60Hz
700mA Dimmable Current Source
40V to 57V Anode Voltage
Fault Output
Yes
Copyright © 2011
Rev. 1.0, 2011-10-03
Microsemi
Analog Mixed Signal Group
11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570
Page 1
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
www.DataSheet.co.kr
LXLMXMG2G220231D-0700040-D2F
TM ® 40W 700mA Dimmable HV LED Driver Module
PRODUCTION DATASHEET
CONDITIONS OF ACCEPTABILITY
The components have been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310.
The input and output leads are 18 AWG, rated 600V, 105ºC, VW-1. The suitability of the leads shall be determined in each end-
use application. The leads are suitable for factory wiring only, and additional investigation will be required for field wiring.
The polymeric housing is rated V-0 and has been subjected to a ball-impact test. The need for a suitable enclosure shall be
considered in the end product.
The component has been evaluated for dry and damp locations, where the humidity conditioning and dielectric tests were
conducted per UL 8750.
The maximum temperature measured on housing outside surface was 61.3°C during the Temperature Test when shifted to
Ambient Temperature 40°C. The necessity of repeated Temperature Test shall be determined in each end use application.
A proper mechanical, electrical and fire enclosure shall be provided in the end-use application that is in compliance with all the
applicable requirements of the end-use application.
Testing was on a 20 A branch circuit. If used on a branch circuit greater than this, additional testing may be necessary.
The LED driver is rated as noted in the Electrical Ratings Table above, and the outputs comply with the requirements for Class
2. The need for additional evaluation shall be considered in the end product if used beyond these ratings.
The LED driver is provided with dimmer leads for connecting an external 0-10 VDC source for dimming the output current. The
leads colors are shown in box below. The dimmer circuit is considered as Class 2 circuit.
Lead Function
AC LINE
AC NEUTRAL
OUTPUT(+)
OUTPUT(-)
RETURN
FAULT
BRITE A
Color
BLACK
WHITE
RED
BLUE
GRAY
BROWN
PURPLE
Copyright © 2011
Rev. 1.0, 2011-10-03
Microsemi
Analog Mixed Signal Group
11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570
Page 5
Da
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet LXMG221D-0700040-D2F.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LXMG221D-0700040-D2F | 40W 700mA Dimmable HV LED Driver Module | Microsemi |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |