|
|
PDF NXA025 Data sheet ( Hoja de datos )
| Número de pieza | NXA025 | |
| Descripción | SMT Non-isolated Power Modules | |
| Fabricantes | Tyco Electronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de NXA025 (archivo pdf) en la parte inferior de esta página. Total 22 Páginas | ||
|
No Preview Available !
Distributed by:
www.Jameco.com ✦ 1-800-831-4242
The content and copyrights of the attached
material are the property of its owner.
www.DataSheet.in
Jameco Part Number 1436359
1 page  
Data Sheet
November 9, 2006
NaosTM NXA025 SMT Non-isolated Power Modules:
10 – 14Vdc Input; 0.8Vdc to 5.5Vdc Output; 25A output current
General Specifications
Parameter
Calculated MTBF (IO=80% of IO, max, TA=25°C)
Weight
Min Typ Max
2,150,000
15.5 (0.55)
Unit
Hours
g (oz.)
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions for additional information.
Parameter
SEQ/ENA Signal Interface
(VIN=VIN, min to VIN, max ; open collector or equivalent,
Signal referenced to GND)
Logic High (SEQ/ENA pin open – Module Off)
SEQ/ENA Current
SEQ/ENA Voltage:
Logic Low (Module ON)
SEQ/ENA Current:
SEQ/ENA Voltage:
Turn-On Delay and Rise Times
(IO=IO, max , Vo to within ±1% of steady state)
Output voltage overshoot – Startup
IO=80% of IO, max; VIN = 12Vdc, TA = 25 oC
Ouptut Overvoltage Protection (Latching)
Input Undervoltage Lockout
Turn-on Threshold
Turn-off Threshold
Remote Sense Range
Overtemperature Protection
(See Thermal Consideration section)
Forced Load Share Accuracy
Number of units in Parallel
Device Symbol Min
Typ
Max
Unit
All
ISEQ/ENA
0.5
All
VSEQ/ENA
3.5
All ISEQ/ENA
All VSEQ/ENA
All Tdelay ―
All Trise ―
All 5.62
All
All 8.1
―
All Tref
All
1
5
0.1
5.8
―
125
10
2.33
14
mA
V
200 µA
1.2 V
― msec
― msec
0.5 % VO, set
6.0 V
9.9 V
V
0.5 V
°C
% Io
5
Tyco Electronics Power Systems
www.DataSheet.in
4
5 Page 
Data Sheet
November 9, 2006
NaosTM NXA025 SMT Non-isolated Power Modules:
10 – 14Vdc Input; 0.8Vdc to 5.5Vdc Output; 25A output current
Feature Description
Remote On/Off using SEQ/ENA Pin
The NXA025A0X-S SMT power modules feature an
SEQ/ENA pin for remote On/Off operation. If not using
the remote On/Off pin, leave the pin open (module will be
on). The SEQ/ENA signal (VSEQ/ENA) is referenced to
ground. Circuit configuration for remote On/Off operation
of the module using SEQ/ENA pin is shown in Figure 25.
During Logic High on the SEQ/ENA pin (transistor Qx is
OFF), the module remains OFF. The external resistor
Rx should be chosen to maintain 3.5V minimum on the
SEQ/ENA pin to insure that the unit is OFF when
transistor Qx is in the OFF state. During Logic-Low
when Qx is turned ON, the module is turned ON. Note
that the external diode is required to make sure the
internal thermal shutdown (THERMAl_SD) and
undervoltage (UVLO) circuits are not disabled when Qx is
turned ON
THERMAL_SD
VIN UVLO
Rx
4.99k
SEQ/ENA
Pin
R1
Dx 1k
Enable
Qx R2
4.99k
Figure 25. Remote On/Off Implementation.
The SEQ/ENA pin can also be used to synchronize the
output voltage start-up and shutdown of multiple modules
in parallel. By connecting SEQ/ENA pins of multiple
modules, the output start-up can be synchronized (please
refer to characterization curves). When SEQ/ENA pins
are connected together, all modules will shutdown if any
one of the modules gets disabled due to undervoltage
lockout or overtemperature protection.
Remote Sense
Remote sense feature minimizes the effects of
distribution losses by regulating the voltage at the remote
sense pins. The voltage between the remote sense pins
and the output terminals must not exceed the remote
sense range given in the Feature Specification table, i.e.:
[Vo(+) – Vo(GND)] –[SENSE(+) – SENSE(-)] < 0.5V
Remote sense configuration is shown in Figure 26. If not
using the remote sense feature to regulate the output
voltage at the point of load, connect SENSE (+) to Vo(+)
and Sense (-) to ground. The amount of power delivered
by the module is defined as the voltage at the output
terminals multiplied by the output current. When using
the remote sense, the output voltage of the module can
be increased, which at the same output current would
increase the power output of the module. Ensure that the
maximum output power of the module remains at or
below the maximum rated power (Po,max = Io,max x
Vo,max).
Figure 26. Effective Circuit Configuration for Remote
sense operation
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally once
the output current is brought back into its specified range.
The average output current during hiccup is 10% IO, max.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, module operation is disabled. The module will begin
to operate at an input voltage above the undervoltage
lockout turn-on threshold.
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with a thermal shutdown circuit. The unit will
shutdown if the thermal reference point Tref, exceeds
125oC (typical), but the thermal shutdown is not
intended as a guarantee that the unit will survive
temperatures beyond its rating. The module will
automatically restarts after it cools down.
Output Voltage Programming
The output voltage of the NXA025A0X-S can be
programmed to any voltage from 0.8Vdc to 5.5Vdc by
inserting a series resistor (shown as Rtrim in figure 27) in
the Sense(+) pin of the module. Without an external
resistor in the Sense(+) pin (Sense (+) pin is shorted to
Vo(+)), the output voltage of the module will be 0.7887V.
With Sense(+) not connected to Vo(+), the output of the
module will reach overvoltage shutdown. A 1µF multi-
layer ceramic capacitor is required from Rtrim to Sense(-)
pin to minimize noise. To calculate the value of the
Tyco Electronics Power Systems
10
www.DataSheet.in
11 Page | ||
| Páginas | Total 22 Páginas | |
| PDF Descargar | [ Datasheet NXA025.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| NXA025 | SMT Non-isolated Power Modules | Tyco Electronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |