|
|
PDF LME49871 Data sheet ( Hoja de datos )
| Número de pieza | LME49871 | |
| Descripción | High Fidelity Current Feedback Audio Operational Amplifier | |
| Fabricantes | National Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LME49871 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
April 28, 2008
LME49871
High Performance, High Fidelity Current Feedback Audio
Operational Amplifier
General Description
The LME49871 is an ultra-low distortion, low noise, ultra high
slew rate current feedback operational amplifier optimized
and fully specified for high performance, high fidelity applica-
tions. Combining advanced leading-edge process technology
with state-of-the-art circuit design, the LME49871 current
feedback operational amplifier delivers superior signal ampli-
fication for outstanding performance. Operating on a wide
supply range of ±5V to ±22V, the LME49871 combines ex-
tremely low voltage noise density (1.9nV/√Hz) with very low
THD+N (0.00012%) to easily satisfy the most demanding ap-
plications. To ensure that the most challenging loads are
driven without compromise, the LME49871 has a high slew
rate of ±1900V/μs and an output current capability of ±100-
mA. Further, dynamic range is maximized by an output stage
that drives 150Ω loads to within 2.9V of either power supply
voltage.
The LME49871 's outstanding CMRR (88dB), PSRR (102dB),
and VOS (0.05mV) give the amplifier excellent operational
amplifier DC performance.
The LME49871 is available in an 8–lead narrow body SOIC.
Demonstration boards are available.
Key Specifications
■ Power Supply Voltage Range
■ THD+N
(AV = 1, RL = 100Ω, VOUT = 2VP-P,
f = 1kHz)
■ THD+N
(AV = 1, RL = 600Ω, VOUT = 1.4VRMS,
f = 1kHz)
■ Input Noise Density
■ Slew Rate
■ Bandwidth
(AV = 1, RL= 2kΩ, RF = 800Ω)
■ Input Bias Current
■ Input Offset Voltage
■ PSRR
■ CMRR
±5V to ±22V
0.00021% (typ)
0.00012% (typ)
1.9nV/√Hz (typ)
±1900V/μs (typ)
213MHz (typ)
1.8μA (typ)
0.05mV (typ)
102dB (typ)
90dB (typ)
Features
■ Easily drives 150Ω loads
■ Optimized for superior audio signal fidelity
■ Output short circuit protection
■ SOIC package
Applications
■ Ultra high quality audio amplification
■ High fidelity preamplifiers
■ High fidelity multimedia
■ State of the art phono pre amps
■ High performance professional audio
■ High fidelity equalization and crossover networks
■ High performance line drivers
■ High performance line receivers
■ High fidelity active filters
© 2008 National Semiconductor Corporation 300426
www.DataSheet.in
www.national.com
1 page  
Typical Performance Characteristics
FFT of 1kHz Sinewave, 0dBr Input Magnitude
VOUT = 3VRMS, RL = 1kΩ, VS = ±15V, AV = 1
FFT of 1kHz Sinewave, 0dBr Input Magnitude
VOUT = 3VRMS, RL = 100Ω, VS = ±15V, AV = 1
30042619
FFT of 1kHz Sinewave, 0dBr Input Magnitude
VOUT = 3VRMS, RL = 600Ω, VS = ±15V, AV = 1
30042620
FFT of 1kHz Sinewave, 0dBr Input Magnitude
VOUT = 1.4VRMS, RL = 1kΩ, VS = ±15V, AV = 1
30042621
FFT of 1kHz Sinewave, 0dBr Input Magnitude
VOUT = 1.4VRMS, RL = 100Ω, VS = ±15V, AV = 1
30042616
FFT of 1kHz Sinewave, 0dBr Input Magnitude
VOUT = 1.4VRMS, RL = 600Ω, VS = ±15V, AV = 1
www.DataSheet.in
30042617
5
30042618
www.national.com
5 Page 
Application Information
GENERAL AMPLIFIER FUNCTION
oltage feedback amplifiers have a small-signal bandwidth that
is a function of the closed-loop gain. Conversely, the
LME49871 current feedback amplifier features a small-signal
bandwidth that is relatively independent of the closed-loop
gain. This is shown in Figure 1 where the LME49871’s gain
is –1,–2, –5 and –10. Like all current feedback amplifiers, the
LME49871’s closed-loop bandwidth is a function of the feed-
back resistance value. Therefore, Rs must be varied to select
the desired closed-loop gain.
POWER SUPPLY BYPASSING AND LAYOUT
CONSIDERATIONS
Properly placed and correctly valued supply bypassing is es-
sential for optimized high-speed amplifier operation. The sup-
ply bypassing must maintain a wideband, low-impedance
capacitive connection between the amplifier’s supply pin and
ground. This helps preserve high speed signal and fast tran-
sient fidelity. The bypassing is easily accomplished using a
parallel combination of a 10μF tantalum and a 0.1μF ceramic
capacitors for each power supply pin. The bypass capacitors
should be placed as close to the amplifier power supply pins
as possible.
FEEDBACK RESISTOR SELECTION (Rf)
The value of the Rf, is also a dominant factor in compensating
the LME49871. For general applications, the LME49871 will
maintain specified performance with an 1.2kΩ feedback re-
sistor. Although this value will provide good results for most
applications, it may be advantageous to adjust this value
slightly for best pulse response optimized for the desired
bandwidth. In addition to reducing bandwidth, increasing the
feedback resistor value also reduces overshoot in the time
domain response.
SLEW RATE CONSIDERATIONS
A current feedback amplifier’s slew rate characteristics are
different than that of voltage feedback amplifiers. A voltage
feedback amplifier’s slew rate limiting or non-linear amplifier
behavior is dominated by the finite availability of the first stage
tail current charging the second stage voltage amplifier’s
compensation capacitor. Conversely, a current feedback
amplifier’s slew rate is not constant. Transient current at the
inverting input determines slew rate for both inverting and
non-inverting gains. The non-inverting configuration slew rate
is also determined by input stage limitations. Accordingly,
variations of slew rates occur for different circuit topologies.
DRIVING CAPACITIVE LOADS
The LME49871 can drive significantly higher capacitive loads
than many current feedback amplifiers. Although the
LME49871 can directly drive as much as 100pF without os-
cillating, the resulting response will be a function of the feed-
back resistor value.
CAPACITIVE FEEDBACK
It is quite common to place a small lead-compensation ca-
pacitor in parallel with a voltage feedback amplifier’s feedback
resistance, Rf. This compensation reduces the amplifier’s
peaking in the frequency domain and damps the transient re-
sponse. Whereas this yields the expected results when used
with voltage feedback amplifiers, this technique must not be
used with current feedback amplifiers. The dynamic
impedance of capacitors in the feedback loop reduces the
amplifier’s stability. Instead, reduced peaking in the frequency
response and bandwidth limiting can be accomplished by
adding an RC circuit to the amplifier’s input.
300426p0
FIGURE 1. Bandwidth as a function of gain
www.DataSheet.in
11
www.national.com
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet LME49871.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LME49870 | LME49870 44V Single High Performance High Fidelity Audio Operational Amplifier (Rev. C) |  Texas Instruments |
| LME49870 | High Fidelity Audio Operational Amplifier | National Semiconductor |
| LME49871 | High Performance High Fidelity Current Feedback Audio Operational Amplifier (Rev. C) | Texas Instruments |
| LME49871 | High Fidelity Current Feedback Audio Operational Amplifier | National Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |