|
|
PDF LTC4069-4.4 Data sheet ( Hoja de datos )
| Número de pieza | LTC4069-4.4 | |
| Descripción | Standalone 750mA Li-Ion Battery Charger in 2 x 2 DFN | |
| Fabricantes | Linear Technology | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LTC4069-4.4 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
LTC4069-4.4www.DataSheet4U.com
FEATURES
Standalone 750mA Li-Ion
Battery Charger in 2 × 2 DFN
with NTC Thermistor Input
DESCRIPTION
n Complete Linear Charger in 2mm × 2mm DFN
Package
n C/10 Charge Current Detection Output
n Timer Charge Termination
n Charge Current Programmable Up to 750mA with
5% Accuracy
n No External MOSFET, Sense Resistor or Blocking
Diode Required
n NTC Thermistor Input for Temperature Qualified
Charging
n Preset 4.4V Float Voltage with 0.6% Accuracy
n Constant-Current/Constant-Voltage Operation with
Thermal Feedback to Maximize Charge Rate
Without Risk of Overheating
n Charge Current Monitor Output for Gas Gauging
n Automatic Recharge
n Charges Single-Cell Li-Ion Batteries Directly from
USB Port
n 20μA Supply Current in Shutdown Mode
n Soft-Start Limits Inrush Current
n Tiny 6-Lead (2mm × 2mm) DFN Package
APPLICATIONS
n Wireless PDAs
n Cellular Phones
n Portable Electronics
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
Protected by U.S. Patents, including 6522118, 6700364.
The LTC®4069-4.4 is a complete constant-current/
constant-voltage linear charger for high capacity single-cell
lithium-ion batteries with a 4.4V float voltage. The 2mm
× 2mm DFN package and low external component count
make the LTC4069-4.4 especially well-suited for portable
applications. Furthermore, LTC4069-4.4 is specifically
designed to work within USB power specifications.
The CHRG pin indicates when charge current has dropped
to ten percent of its programmed value (C/10). An
internal timer terminates charging according to battery
manufacturer specifications.
No external sense resistor or blocking diode is required due to
the internal MOSFET architecture. Thermal feedback regulates
charge current to limit the die temperature during high power
operation or high ambient temperature conditions.
When the input supply (wall adapter or USB supply) is
removed, the LTC4069-4.4 automatically enters a low current
state, dropping battery drain current to less than 1μA. With
power applied, LTC4069-4.4 can be put into shutdown mode,
reducing the supply current to less than 20μA.
The LTC4069-4.4 also includes automatic recharge, low-
battery charge conditioning (trickle charging), soft-start
(to limit inrush current) and an NTC thermistor input used
to monitor battery temperature.
The LTC4069-4.4 is available in a tiny 6-lead, low profile
(0.75mm) 2mm × 2mm DFN package.
TYPICAL APPLICATION
Standalone Li-Ion Battery Charger
VIN
4.5V TO 5.5V
RNOM
100k
R1
510Ω
RNTC
100k
1μF
VCC BAT
LTC4069-4.4
CHRG PROG
NTC GND
500mA
+
RPROG
2k
4.4V
Li-Ion
BATTERY*
4069 TA01
*E.G. SANYO BATTERIES: UF553436T OR UF553450T
Complete Charge Cycle (1100mAh Battery)
550
500 CONSTANT-CURRENT
4.5
4.4
450
400
350 CONSTANT-
300 VOLTAGE
CHRG
TRANSITION
4.3
4.2
4.1
4.0
250 3.9
200 3.8
150
100
50
0
0
3.7
CHARGE
3.6
VCC = 5V
TERMINATION
3.5
RPROG = 2K
3.4
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
TIME (HOURS)
4069 TA01b
406944fa
1
1 page  
TYPICAL PERFORMANCE CHARACTERISTICS
LTC4069-4.4www.DataSheet4U.com
Undervoltage Lockout Threshold
Voltage vs Temperature
4.00
3.75
RISE
3.50
Trickle Charge Current
vs Supply Voltage
60
VBAT = 2V
TA = 25°C
50
RPROG = 2k
40
Trickle Charge Current
vs Temperature
60
VCC = 5V
VBAT = 2V
50
RPROG = 2k
40
3.25
FALL
3.00
2.75
30
20
RPROG = 10k
10
30
20
RPROG = 10k
10
2.50
–50 –25 0
25 50
TEMPERATURE (°C)
75 100
4069 G16
CHRG Pin Output Low Voltage
vs Temperature
140
VCC = 5V
120 ICHRG = 5mA
100
80
60
40
20
0
–50 –25
0
25 50 75
TEMPERATURE (oC)
100
4069 G10
0
4 4.5 5 5.5 6
SUPPLY VOLTAGE (V)
4069 G14
0
–50 –25
0
25 50 75 100
TEMPERATURE (°C)
4069 G15
Timer Accuracy vs Temperature
1
VCC = 5V
0
–1
–2
–3
–4
–5
–6
–7
–50 –25
0
25 50 75 100
TEMPERATURE (°C)
4069 G18
Timer Accuracy vs Supply Voltage
2.0
TA = 25°C
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
4
4.5 5 5.5
SUPPLY VOLTAGE (V)
6
4069 G19
PROG Pin Shutdown Voltage
Threshold vs Temperature
5.0
VCC = 5V
4.5
PROG Pin Shutdown Voltage
vs Supply Voltage
5.0 TA = 25°C
4.5
4.0
4.0 3.5
3.0
3.5
2.5
3.0
–50
–25 0 25 50
TEMPERATURE (°C)
75 100
4069 G20
2.0
4
4.5 5 5.5
SUPPLY VOLTAGE (V)
6
4069 G21
406944fa
5
5 Page 
OPERATION
VCC
RNOM
0.76 • VCC
NTC
6
RNTC
0.35 • VCC
0.016 • VCC
–
+
–
+
+
–
TOO COLD
TOO HOT
NTC_ENABLE
LTC4069-4.4www.DataSheet4U.com
Figure 3. NTC Circuit Information
4069 F03
APPLICATIONS INFORMATION
Undervoltage Charge Current Limiting (UVCL)
The LTC4069-4.4 includes undervoltage charge (ΔVUVCL1)
current limiting that prevents full charge current until the
input supply voltage exceeds approximately 220mV above
the battery voltage. This feature is particularly useful if the
LTC4069-4.4 is powered from a supply with long leads (or
any relatively high output impedance).
For example, USB-powered systems tend to have highly
variable source impedances (due primarily to cable
quality and length). A transient load combined with such
impedance can easily trip the UVLO threshold and turn the
charger off unless undervoltage charge current limiting
is implemented.
Consider a situation where the LTC4069-4.4 is operating
under normal conditions and the input supply voltage
begins to droop (e.g., an external load drags the input
supply down). If the input voltage reaches VBAT + ΔVUVCL1
(approximately 220mV above the battery voltage),
undervoltage charge current limiting will begin to reduce
the charge current in an attempt to maintain ΔVUVCL1
between the VCC input and the BAT output of the IC.
The LTC4069-4.4 will continue to operate at the reduced
charge current until the input supply voltage is increased
or constant-voltage mode reduces the charge current
further.
Operation from Current Limited Wall Adapter
By using a current limited wall adapter as the input supply,
the LTC4069-4.4 dissipates significantly less power when
programmed for a current higher than the limit of the supply
as compared to using a non-current limited supply at the
same charge current.
Consider a situation where an application demands a
600mA charge current for an 800mAh Li-Ion battery. If a
typical 5V (non-current limited) input supply is used, the
charger’s peak power dissipation can exceed 1W.
Now consider the same scenario, but with a 5V input
supply with a 600mA current limit. To take advantage
of the current limited supply, it is necessary to program
the LTC4069-4.4 to charge at a current above 600mA.
Assume that the LTC4069-4.4 is programmed for 750mA
(i.e., RPROG= 1.33k) to ensure that part tolerances maintain
406944fa
11
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet LTC4069-4.4.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LTC4069-4.4 | Standalone 750mA Li-Ion Battery Charger in 2 x 2 DFN | Linear Technology |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |