|
|
PDF ALN0925AT Data sheet ( Hoja de datos )
| Número de pieza | ALN0925AT | |
| Descripción | Internally Matched LNA Module | |
| Fabricantes | Advanced Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ALN0925AT (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
plerowTM ALN0925AT
Internally Matched LNA Module
Features
· S21 = 20.5 dB @ 890 MHz
= 19.5 dB @ 960 MHz
· NF of 0.8 dB over Frequency
· Unconditionally Stable
· Single 5V Supply
· High OIP3 @ Low Current
Description
The plerowTM ALN-series is the compactly designed surface-mount
module for the use of the LNA with or without the following gain blocks in
the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS,
PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communi-
cation terminals, CATV and so on. It has an exceptional performance of
low noise figure, high gain, high OIP3, and low bias current. The stability
factor is always kept more than unity over the application band in order
to ensure its unconditionally stable implementation to the application
system environment. The surface-mount module package including the
completed matching circuit and other components necessary just in case
allows very simple and convenient implementation onto the system
board in mass production level.
Specifications (in Production)
Typ. @ T = 25°C, Vs = 5 V, Freq. = 925 MHz, Zo.sys = 50 ohm
Parameter
Unit Specifications
Min Typ Max
Frequency Range
MHz
890
960
Gain
dB 19 20
Gain Flatness
dB
± 0.5
± 0.7
Noise Figure
dB
0.8 0.85
Output IP3 (1)
dBm 30 31
S11 / S22 (2)
dB
-14 / -14
Output P1dB
dBm 16 17
Switching Time
µsec
-
Supply Current
mA
70 80
Supply Voltage
Impedance
V
Ω
5
50
Max. RF Input Power
dBm
C.W 29 ~ 31 (before fail)
Package Type & Size
mm Surface Mount Type, 10Wx10Lx3.8H
Operating temperature is -40°C to +85°C.
1) OIP3 is measured with two tones at an output power of 8 dBm / tone separated by 1 MHz.
2) S11/S22 (max) is the worst value within the frequency band.
3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to VS.
Outline Drawing (Unit: mm)
1-stage Single Type
More Information
Website: www.asb.co.kr
E-mail: [email protected]
Tel: (82) 42-528-7223
Fax: (82) 42-528-7222
ASB Inc., 4th Fl. Venture Town
Bldg., 367-17 Goijeong-Dong,
Seo-Gu, Daejon 302-716, Korea
plerow
ALN0925AT
ASB Inc.
(Top View)
Solder Stencil Area
(Bottom View)
(Side View)
Ø0.4 plated thru holes to ground plane
1/5
(Recommended Footprint)
www.asb.co.kr
Pin Number
2
5
6
Others
Function
RF In
RF Out
+Vcc
Ground
Note: 1. The number and size of ground via holes in
a circuit board is critical for thermal RF
grounding considerations.
2. We recommend that the ground via holes be
placed on the bottom of all ground pins for
better RF and thermal performance, as
shown in the drawing at the left side.
November 2008
1 page  
www.DataSheet4U.com
Application Circuit
V DC
plerowTM ALN0925AT
Internally Matched LNA Module
+-
Tantal
Capacitor
IN
C1
ALN
OUT
C2
1) The tantal capacitor is optional and for bypassing the AC noise introduced from the DC supply.
The capacitance value may be determined by customer’s DC supply status.
2) So-called DC blocking capacitors are always necessarily placed at the input and output port
for allowing only the RF signal to pass and blocking the DC component in the signal. The DC
blocking capacitors are included inside the LNA module. Therefore, C1 & C2 capacitors may
not be necessary, but can be added just in case that the customer wants. The value of C1 &
C2 is determined by considering the application frequency.
Recommended Soldering Reflow Process
260°C
20~40 sec
200°C
Ramp-up
(3˚C/sec)
Ramp-down
(6°C/sec)
150°C
60~180 sec
Evaluation Board Layout
+Vcc
IN OUT
Size 25 x 25mm
(for ALN-AT, BT, T Series – 10x10mm)
5/5
www.asb.co.kr
November 2008
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet ALN0925AT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ALN0925AT | Internally Matched LNA Module | Advanced Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |