|
|
PDF MKP10 Data sheet ( Hoja de datos )
| Número de pieza | MKP10 | |
| Descripción | Polypropylene Capacitors | |
| Fabricantes | WMA | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MKP10 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
WIMA MKP 10
Powlwywp.DroatpaSyhleeent4eU.(cPoPm) Capacitors for Pulse Applications with
Double-Sided Metallized Electrodes and Schoopage Contacts
PCM 7.5 mm to 37.5 mm
D
Special Features
Electrical Data
˜ Pulse duty construction
˜ Self-healing
˜ Very low dissipation factor
˜ Negative capacitance change
versus temperature
˜ According to RoHS 2002/95/EC
Typical Applications
For pulse applications e.g.
˜ Switch mode power supplies
˜ TV and monitor sets
˜ Lighting
˜ Audio/video equipment
Construction
Dielectric: Polypropylene (PP) film
Capacitor electrodes:
Double-sided metallized plastic film
Internal construction:
MKP 10: 63 VAC, 180 VAC, 250 VAC
Plastic film
Electrode carrier
plastic film metallized
on both sides
Metal contact layer
(schoopage)
Terminating wire
MKP 10: 400 VAC, 600 VAC, 650 VAC, 700 VAC
Plastic film
Electrode carrier
plastic film metallized
on both sides
Plastic film metallized
on one side
Metal contact layer
(schoopage)
Terminating wire
MKP 10: 900 VAC (PCM 15 = 3-section)
Plastic film
Electrode carrier
plastic film metallized
on both sides
Plastic film metallized
on one side
Metal contact layer
(schoopage)
Terminating wire
Encapsulation:
Solvent-resistant, flame-retardant plastic
case with epoxy resin seal, UL 94 V-0
Terminations: Tinned wire.
Marking: Colour: Red.
Marking: Black. Epoxy resin seal: Red
Capacitance range:
1000 pF to 15 mF (E12-values on request)
Rated voltages:
100 VDC, 250 VDC, 400 VDC, 630 VDC,
1000 VDC, 1600 VDC, 2000 VDC, 2500 VDC
Capacitance tolerances:
±20%, ±10%, ±5%
Operating temperature range:
–55) C to +100) C
Climatic test category:
55/100/56 in accordance with IEC
Insulation resistance at +20+ C:
C T 0.33 mF: 1 x 105 M¸
(mean value: 5 x 105 M¸)
C 0.33 mF: 30 000 sec (M¸ x mF)
(mean value: 100 000 sec)
Measuring voltage: 100 V/1 min.
Dissipation factors at + 20) C: tan d
Test voltage: 1.6 Ur, 2 sec.
Dielectric absorption:
0.05 %
Voltage derating:
A voltage derating factor of 1.35 % per K
must be applied from +85+ C for DC
voltages and from +75+ C for AC
voltages.
Reliability:
Operational life 300 000 hours
Failure rate 1 fit (0.5 x Ur and 40) C)
at f
C 0.1 mF
0.1 mF < C T 1.0 mF
C > 1.0 mF
1 kHz
10 kHz
100 kHz
3 x 10-4
4 x 10-4
15 x 10-4
3 x 10-4
6 x 10-4
–
3 x 10-4
–
–
Maximum pulse rise time:
Capacitance max. pulse rise time V/msec at TA < 40) C
pF/mF
100 VDC 250 VDC 400 VDC 630 VDC 1000 VDC 1600 VDC 2000 VDC 2500 VDC
1000 ... 2200 1000 1800 1800 1800 2800 5400 9000
3300 ... 6800 900 1200 1200 1200 2800 5400 9000
0.01 ... 0.022 700 1100 1200 1800 2100 3000 3400
0.033 ... 0.068 400 800 900 1800 2100 2100 2100
0.1 ... 0.22 200 500 500 900 1400 1400 1400
0.33 ... 0.68 100 300 400 700 900 900 900
1.0 ... 2.2 70 200 200 400 400 500 –
3.3 ... 4.7 50 80 100 150 – – –
6.8 ... 15 35 50 70 – – – –
11000
11000
11000
–
–
–
–
–
–
for pulses equal to the rated voltage
Mechanical Tests
Packing
Pull test on leads:
d T 0.8 l: 10 N in direction of leads
d > 0.8 l: 20 N in direction of leads
according to IEC 60068-2-21
Vibration:
6 hours at 10 ... 2000 Hz and 0.75 mm
displacement amplitude or 10 g in
accordance with IEC 60068-2-6
Low air density:
1kPa = 10 mbar in accordance with
IEC 60068-2-13
Bump test:
4000 bumps at 390 m/sec2
in accordance with IEC 60068-2-29
Available taped and reeled up to and
including case size 15 x 26 x 31.5 /
PCM 27.5 mm.
Detailed taping information and graphs
at the end of the catalogue.
For further details and graphs please
refer to Technical Information.
68
1 page  
Recommendation for Processing
and Application of
Thwrwow.uDgatahS-hHeeot4Ule.coCm apacitors
D
Soldering Process
A preheating of through-hole WIMA
capacitors is allowed for temperatures
Tmax P 100 ° C.
In practice a preheating duration of
t P 5 min. has been proven to be best.
Single wave soldering
Soldering bath temperature: T P 260 ° C
Immersion time:
t P 5 sec
Double wave soldering
Soldering bath temperature: T P 260 ° C
Immersion time:
2 x t P 3 sec
Due to different soldering processes and
heat requirements the graphs are to be
regarded as a recommendation only.
Wave soldering
T [°C]
10 s
260
240
see detail-
enlargement
220
200
180
160
140
120
100
80
60
40
20 30 60
90
2s 3s
t
120 150 180 210 240 [sec]
Typical temperature/time graph for double wave soldering
WIMA Quality and Environmental Philosophy
ISO 9001:2000 Certification
WIMA Environmental Policy
RoHS Compliance
ISO 9001:2000 is an international basic
standard of quality assurance systems for
all branches of industry. The approval
according to ISO 9001:2000 of our
factories by the VDE inspectorate certifies
that organisation, equipment and moni-
toring of quality assurance in our factories
correspond to internationally recognized
standards.
WIMA WPCS
The WIMA Process Control System (WPCS)
is a quality surveillance and optimization
system developed by WIMA. WPCS is a
major part of the quality-oriented WIMA
production. Points of application of WPCS
during production process:
” incoming material inspection
” metallization
” film inspection
” schoopage
” pre-healing
” lead attachment
” cast resin preparation/
encapsulation
” 100% final inspection
” AQL check
All WIMA capacitors, irrespective of
whether through-hole devices or SMD,
are made of environmentally friendly
materials. Neither during manufacture
nor in the product itself any toxic
substances are used, e.g.
– Lead
– PCB
– CFC
– Hydrocarbon chloride
– Chromium 6+
– PBB/PBDE
– Arsenic
– Cadmium
– Mercury
– etc.
We merely use pure, recyclable materials
for packing our components, such as:
” carton
” cardboard
” adhesive tape made of paper
” polystyrene
We almost completely refrain from using
packing materials such as:
” foamed polystyrene (Styropor®)
” adhesive tapes made of plastic
” metal clips
According to the RoHS Directive 2002/95/EC
certain hazardous substances like e.g. lead,
cadmium, mercury must not be used any
longer in electronic equipment as of July 1st,
2006. For the sake of the environment WIMA
has refraind from using such substances since
years already.
Tape for lead-free WIMA capacitors
DIN EN ISO 14001:2005
WIMA’s environmental management has
been established in accordance with the
guidelines of DIN EN ISO 14001:2005.
The certification has been granted in
June 2006.
16
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet MKP10.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MKP10 | Polypropylene Capacitors | WMA |
| MKP10-xxxgK | Metallized Polycarbonate Capacitors |  leclanchecap |
| MKP1837 | Metallized Polypropylene Film Capacitor |  Vishay Siliconix |
| MKP1839 | AC and Pulse Metallized Polypropylene Film Capacitors | Vishay Siliconix |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |