|
|
PDF AA51883 Data sheet ( Hoja de datos )
| Número de pieza | AA51883 | |
| Descripción | SERVO MOTOR CONTROLLER | |
| Fabricantes | Agamem Microelectronic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AA51883 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
AA51883Agamem Microelectronics Inc.
wPwwR.DEatLaSIhMeetI4NU.AcomRY
SERVO MOTOR CONTROLLER
■ DESCRIPTION
The AA51883 is an integrated circuit to be applied on servo motor of radio controlled
operation. It provides some flexible functions to tune the servo. External PNP driver will be
chosen for servo motor application.
■ FEATURES
• Internal output NPN power transistor.
• Adjustable dead band range control by external capacitor.
• Fixed pulse width setting to provide start-up power and speed control
• Incorporates a protection circuit for "H-Bridge" driving configuration
■ APPLICATIONS
• Servo motor control.
• Radio controlled car, boat, and airplane.
• IA products (such as air-condition).
• Remote positioning.
■ BLOCK DIAGRAM
VIN 8
Directional
Logic
Control
Sawtooth Wave
& One Shot
Generator
Servo
Position &
Over-Time
Logic
CFP VCC
23
PWM
Control
Pulse
Stretcher
Output
Driver
1 EXP1
16 OUT1
13 OUT2
12 EXP2
Voltage
Regulator
5 VREG
9
10 11
76
15
RT
CT POT
CDB CST
GND
©Copyright Agamem Microelectronics Inc.
1
www.agamem.com.tw 2008/4/9
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER
NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT
ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED
HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
1 page  
AA51883Agamem Microelectronics Inc.
wPwwR.DEatLaSIhMeetI4NU.AcomRY
SERVO MOTOR CONTROLLER
■ FUNCTIONAL DESCRIPTION
(1) Voltage Regulator
This circuit is composed of a band gap circuit, and outputs a 2.5-volt temperature
compensated reference voltage. This reference voltage is stabilized when the supply
voltage is variable.
(2) Saw tooth wave & One-Shot Generator
Connect a capacitor to CT pin will generate a triangular wave by constant current charging.
A typical value is 0.1uF. The constant current is determined by a resistor connected to RT
pin. A typical capacitor of approximately 0.1uF should be connected in parallel with the
resistor to increase stability.
(3) Servo Position & Over-Time logic
This circuitry consists of a pulse width comparator, which compares the servo position
detection signal (POT pin) from the one-shot timer (CT pin) whose period depends on the
resistance of a potentiometer connected to the servo's drive shaft. This feedback provides
the stability for the control circuitry.
(4) Pulse Stretcher
The difference between the servo control signal and the feedback signal is the error signal.
This error signal is used to toggle the direction of the current flows through the servo. The
function of this pulse stretcher is to “stretch” the small error signal long enough and
increases the duty cycle to the motor for it can maintain sufficient holding force. The circuit
also implements a “dead band” function that prevents servo jitter and hunting. This is a
range over which differences between the input and reference signals will not cause servo
operation. When the signal differences exceed this “dead band” range, the servo will start
to shift. The dead band will change according to the value of capacitor connected to the
CDB pin.
(5) Directional Logic Control
The comparator circuit compares pulses from the servo control input (VIN pin) and the
voltage controlled pulse generator. It provides either a positive or a negative output
depending on whether the signal pulse width is larger or smaller than the position
generator’s output pulse (POT pin). Application of this error voltage to the motor driver
circuit causes the motor to turn in a direction that will minimize the error until both pulse
widths are the same.
(6) PWM Control
This signal generated by directional logic control block is used to control a flip-flop that
toggles the direction the current flows through the motor. The outputs of the flip-flop drive
©Copyright Agamem Microelectronics Inc.
5
www.agamem.com.tw 2008/4/9
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER
NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT
ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED
HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet AA51883.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AA51880 | SERVO MOTOR CONTROLLER | Agamem Microelectronic |
| AA51881 | SERVO MOTOR CONTROLLER | Agamem Microelectronic |
| AA51882 | SERVO MOTOR CONTROLLER | Agamem Microelectronic |
| AA51883 | SERVO MOTOR CONTROLLER | Agamem Microelectronic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |