DataSheet.es    


PDF ISL54206A Data sheet ( Hoja de datos )

Número de pieza ISL54206A
Descripción MP3/USB 2.0 High Speed Switch
Fabricantes Intersil Corporation 
Logotipo Intersil Corporation Logotipo



Hay una vista previa y un enlace de descarga de ISL54206A (archivo pdf) en la parte inferior de esta página.


Total 17 Páginas

No Preview Available ! ISL54206A Hoja de datos, Descripción, Manual

®
www.DataSheet4U.com
Data Sheet
MP3/USB 2.0 High Speed Switch with
Negative Signal Handling
The Intersil ISL54206A dual SPDT (Single Pole/Double
Throw) switches combine low distortion audio and accurate
USB 2.0 high speed data (480Mbps) signal switching in the
same low voltage device. When operated with a 2.7V to 3.6V
single supply these analog switches allow audio signal
swings below-ground, allowing the use of a common USB
and audio headphone connector in Personal Media Players
and other portable battery powered devices.
The ISL54206A logic control pins are 1.8V compatible which
allows for control via a standard µcontroller. With a VDD
voltage in the range of 2.7V to 3.6V the IN pin voltage can
exceed the VDD rail allowing for the USB 5V VBUS voltage
from a computer to directly drive the IN pin to switch
between the audio and USB signal sources in the portable
device. The part has an audio enable control pin to open all
the switches and put the part in a low power state.
The ISL54206A is available in a small 10 Ld 2.1mmx1.6mm
ultra-thin µTQFN package and a 10 Ld 3mmx3mm TDFN
package. It operates over a temperature range of -40 to
+85°C.
Related Literature
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
• Application Note AN557 “Recommended Test Procedures
for Analog Switches”
Application Block Diagram
June 25, 2007
ISL54206A
FN6515.0
Features
• High Speed (480Mbps) and Full Speed (12Mbps)
Signaling Capability per USB 2.0
• Low Distortion Negative Signal Capability
• Control Pin to Open all Switches and Enter Low Power
State
• Low Distortion Headphone Audio Signals
- THD+N at 20mW into 32Ω Load . . . . . . . . . . . . . <0.1%
• Cross-talk Audio Channels (20Hz to 20kHz) . . . . . -110dB
• Single Supply Operation (VDD) . . . . . . . . . . . . 2.5V to 5.5V
• -3dB Bandwidth USB Switches . . . . . . . . . . . . . . . 630MHz
• Available in µTQFN and TDFN Packages
• Pb-Free Plus Anneal (RoHS Compliant)
• Compliant with USB 2.0 Short Circuit Requirements
Without Additional External Components
Applications
• MP3 and Other Personal Media Players
• Cellular/Mobile Phones
• PDA’s
• Audio/USB Switching
VBUS
IN
COM-
VDD
ISL54206A
LOGIC CIRCUITRY
4MΩ
CTRL
D-
D+
COM+
50kΩ
L
R
50kΩ
GND
µCONTROLLER
USB
HIGH-SPEED
TRANSCEIVER
CODEC
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.

1 page




ISL54206A pdf
ISL54206A
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V, VCTRLH = 1.4V,
VCTRLL = 0.5V, (Notes 4), unless otherwise specified. (Continued)
www.DataSheet4U.com
PARAMETER
TEST CONDITIONS
TEMP MIN
MAX
(°C) (Notes 5, 8) TYP (Notes 5, 8) UNITS
DIGITAL INPUT CHARACTERISTICS
Voltage Low, VINL , VCTRLL
Voltage High, VINH, VCTRLH
Input Current, IINL, ICTRLL
Input Current, IINH
Input Current, ICTRLH
CTRL Pull-Down Resistor, RCTRL
NOTES:
VDD = 2.7V to 3.6V
VDD = 2.7V to 3.6V
VDD = 3.6V, IN = 0V, CTRL = 0V
VDD = 3.6V, IN = 3.6V, CTRL = 0V
VDD = 3.6V, IN = 0V, CTRL = 3.6V
VDD = 3.6V, IN = 0V, CTRL = 3.6V
Full -
- 0.5 V
Full 1.4
-
-V
Full -50
20
50 nA
Full -50
20
50 nA
Full -2
1.1
2 μA
Full - 4 - MΩ
4. VLOGIC = Input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range..
7. RON matching between channels is calculated by subtracting the channel with the highest max RON value from the channel with lowest max
RON value, between L and R or between D+ and D-.
8. Parts are 100% tested at +25°C. Over temperature limits established by characterization and are not production tested.
Test Circuits and Waveforms
LOGIC
INPUT
VDD
0V
50%
tOFF
tr <20ns
tf <20ns
SWITCH
INPUT
VINPUT
SWITCH
OUTPUT
0V
VOUT
90%
tON
90%
Logic input waveform is inverted for switches that have the opposite
logic sense.
VDD
C
VINPUT
SWITCH
INPUT
CTRL
AUDIO or USB
IN
COMx
VIN GND
VOUT
RL CL
50Ω 10pF
Repeat test for all switches. CL includes fixture and stray
capacitance.
VOUT
=
V (INPUT)
------------R-----L-------------
RL + R(ON)
FIGURE 1A. MEASUREMENT POINTS
FIGURE 1. SWITCHING TIMES
FIGURE 1B. TEST CIRCUIT
5 FN6515.0
June 25, 2007

5 Page





ISL54206A arduino
ISL54206A
Typical Performance Curves TA = +25°C, Unless Otherwise Specified
w0.w11w.DRaLtaOSAhDe=e3t42UΩ.com
0.1 VLOAD = 0.707VRMS
0.4
RLOAD = 32Ω
VDD = 3V
0.09
VDD = 2.6V
0.3
3VP-P
0.08
0.07
0.06
0.05
VDD = 2.7V
VDD = 3V
VDD = 3.6V
0.2
0.1
2.5VP-P
2VP-P
0.04
20
200 2k
FREQUENCY (Hz)
20k
FIGURE 8. THD+N vs SUPPLY VOLTAGE vs FREQUENCY
1VP-P
0
20 200
2k 20k
FREQUENCY (Hz)
FIGURE 9. THD+N vs SIGNAL LEVELS vs FREQUENCY
0.5
RLOAD = 32Ω
FREQ = 1kHz
0.4 VDD = 3V
0.3
0.2
0.1
0
0 0.5 1 1.5 2 2.5 3
OUTPUT VOLTAGE (VP-P)
FIGURE 10. THD+N vs OUTPUT VOLTAGE
3.5
0.5
RLOAD = 32Ω
FREQ = 1kHz
VDD = 3V
0.4
0.3
0.2
0.1
0
0 10 20 30 40
OUTPUT POWER (mW)
FIGURE 11. THD+N vs OUTPUT POWER
50
11 FN6515.0
June 25, 2007

11 Page







PáginasTotal 17 Páginas
PDF Descargar[ Datasheet ISL54206A.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ISL54206MP3/USB 2.0 High Speed SwitchIntersil Corporation
Intersil Corporation
ISL54206AMP3/USB 2.0 High Speed SwitchIntersil Corporation
Intersil Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar