|
|
PDF STPIC44L02 Data sheet ( Hoja de datos )
| Número de pieza | STPIC44L02 | |
| Descripción | 4 CHANNEL SERIAL AND PARALLEL LOW SIDE PRE-FET DRIVER | |
| Fabricantes | STMicroelectronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de STPIC44L02 (archivo pdf) en la parte inferior de esta página. Total 21 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
STPIC44L02
4 CHANNEL SERIAL AND PARALLEL
LOW SIDE PRE-FET DRIVER
s 4-CHANNEL SERIAL-IN PARALLEL-IN LOW
SIDE PRE-FET DRIVER
s DEVICES ARE CASCADABLE
s INTERNAL 55V INDUCTIVE LOAD CLAMP
AND VGS PROTECTION CLAMP FOR
EXTERNAL POWER FETS
s INDEPENDENT SHORTED-LOAD AND
SHORT-TO-BATTERY FAULT DETECTION
ON ALL GATE TERMINALS
s INDEPENDENT OFF-STATE OPEN-LOAD
FAULT SENSE
s OVER-BATTERY-VOLTAGE LOCKOUT
PROTECTION AND FAULT REPORTING
s UNDER-BATTERY VOLTAGE LOCKOUT
PROTECTION
s ASYNCRONOUS OPEN-GATE FAULT FLAG
s DEVICE OUTPUT CAN BE WIRED OR WITH
MULTIPLE DEVICES
s FAULT STATUS RETURNED THROUGH
SERIAL OUTPUT TERMINAL
s INTERNAL GLOBAL POWER-ON RESET OF
DEVICE AND EXTERNAL RESET TERMINAL
s HIGH IMPEDANCE CMOS COMPATIBLE
INPUTS WITH HYSTERESIS
s TRANSITION FROM THE GATE OUTPUT TO
A LOW DUTY CYCLE PWM MODE WHEN A
SHORTED LOAD FAULT OCCURS
DESCRIPTION
The STPIC44L02 is a low-side predriver that
provides serial and parallel input interfaces to
control four external FET power switches.
It is mainly designed to provide low-frequency
switching, inductive load applications such as
solenoids and relays. Fault status is available in a
serial-data format. Each driver channel has
independent off-state open-load detection and
on-state shorted load short to battery detection.
The STPIC44L02 offers a battery over voltage and
undervoltage detection and shutdown. If a fault
occurs while using the STPIC44L02, the channel
transitates into a low duty cycle, pulse width
modulated (PWM) signal as long as the fault is
present.
These devices provide control of output channels
through a serial input interface or a parallel input
interface. A command to enable the output from
July 2003
SOP
either interface enables the respective channels
gate output to the external FET. The serial
interface is recommended when the number of
signals between the control device and the
predriver are minimized and the speed of
operation is not critical. In applications where the
predriver must respond very quickly or
asynchronously, the parallel input interface is
recommended.
For serial operation, the control device must
transitate CS from high to low to activate the serial
input interface. When this occurs, SDO, is
enabled, fault data is latched into the serial
interface, and the fault flag is refreshed. Data is
clocked into the serial registers on low to high
transitions of SCLK through SDI. Each string of
data must consist of at least four bits of data. In
applications where multiple devices are cascaded
together, the string of data must consist of four bits
for each device. A high data bit turns the
respective output channel on and a low data bit
turns it off. Fault data for the device is clocked out
of SDO as serial input data is clocked into the
device. Fault data consists of fault flags for
shorted load and open load flags (bits 0-3) for
each of the four output channels. Fault register
bits are set or cleared asynchronously to reflect
the current state of the hardware. A fault must be
present when CS is transitated from high to low to
be captured and reported in the serial fault data.
New faults cannot be captured in the serial
register when CS is low. CS must be transitated
high after all of the serial data has been clocked
into the device. A low to high transition of CS
transfers the last four bits of serial data to the
1/21
1 page  
www.DataSheet4U.com
Figure 2 : Pin Configuration
STPIC44L02
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
VCC
VBAT
VI
VO
VO
VI
VDS
TC
TJ
Tstg
Logic Supply Voltage (See Note 1)
Battery Supply Voltage
Logic Input Voltage Range
Output Voltage (SDO and FLT)
Output Voltage
Logic Input Voltage Range
Drain to Source Voltage
Operating Case Temperature Range
Maximum Junction Temperature
Storage Temperature Range
-0.3 to 7
-0.3 to 60
-0.3 to 7
-0.3 to 7
-0.3 to 15
-0.3 to 7
-0.3 to 60
-40 to +125
150
-40 to +150
V
V
V
V
V
V
V
°C
°C
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is
not implied.
Note 1: All voltage value are with respect to GND
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
VBAT
VIH
VIL
ts
th
TC
Parameter
Logic Supply Voltage
Battery Supply Voltage
High Level Input Voltage
Low Level Input Voltage
Set-up Time, SDI High Before SCLK ↑
Hold Time, SDI High After SCLK ↑
Operating Case Temperature
Min.
4.5
8
0.85VCC
0
10
10
-40
Min.
5
Max.
5.5
24
VCC
0.15VCC
125
Unit
V
V
V
V
ns
ns
°C
5/21
5 Page 
www.DataSheet4U.com
Figure 10 : Serial Programming Example
STPIC44L02
Figure 11 : 8-Bit Serial Programming Example (single device)
11/21
11 Page | ||
| Páginas | Total 21 Páginas | |
| PDF Descargar | [ Datasheet STPIC44L02.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| STPIC44L02 | 4 CHANNEL SERIAL AND PARALLEL LOW SIDE PRE-FET DRIVER | STMicroelectronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |