|
|
Número de pieza | AP1212 | |
Descripción | DUAL USB HIGH-SIDE POWER SWITCH | |
Fabricantes | Diodes Incorporated | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de AP1212 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
No Preview Available ! Features
• Compliant to USB specifications
• Dual independent switches control
• 2.7V to 5.5V input voltage
• 500mA minimum continuous current per port
• 110mΩ typical on-resistance
• 1.25A maximum short circuit current limit
• Independent open-drain fault flag pins
• 110μA typical on-state supply current
• 1μA typical off-state supply current
• Output can be forced higher than input (off-state)
• Thermal shutdown
• 2.4V typical under voltage lockout (UVLO)
• 1ms turn-on (soft-start) and fast turn-off
• Enable active-high (H) or active-low (L)
• SOP-8L: Available in “Green” Molding Compound
(No Br, Sb)
• Lead Free Finish/RoHS Compliant (Note 1)
Applications
• USB hubs
• Hot plug-in power supplies
• Battery-charger circuits
AP1212
DUAL USB HIGH-SIDE POWER SWITCH
General Description
The AP1212 series are dual integrated high-side power switch
with independent enable and flag functions, optimized for
self-powered and bus-powered Universal Serial Bus (USB)
applications. The AP1212 series support the following USB
requirements: each switch channel supplies up to 500mA as
required by USB downstream devices; the switch’s low
on-resistance meets USB voltage drop requirements; fault
current is limited to typically 1000mA, well below the UL 25VA
safety requirements; and a flag output is available to indicate fault
conditions to the local USB controller. Soft start eliminates the
momentary voltage drop on the upstream port that may occur
when the switch is enabled in bus-powered applications.
Additional features include thermal shutdown to prevent
catastrophic switch failure from high-current loads, under voltage
lockout (UVLO) to ensure that the device remains off unless there
is a valid input voltage present, and 3.3V and 5V logic compatible
enable inputs.
Ordering Information
A P1212 X X X X
Enable
H : Active - High
L : Active - Low
Package
S : SOP - 8L
Lead Free
L : Lead Free
G : Green
Packing
- U : Tube
-13 : Taping
Note:
1. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7.
Device
(Note 3)
AP1212XS
Package
Code
Packaging
S SOP-8L
Tube
Quantity
Part Number
Suffix
100 -U
13” Tape and Reel
Quantity
Part Number
Suffix
2500/Tape & Reel
-13
Note: 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be on found our website at
http://www.diodes.com/datasheets/ap02001.pdf.
AP1212 Rev. 2
1 of 12
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
1 page AP1212
DUAL USB HIGH-SIDE POWER SWITCH
Typical Performance Characteristics
On-Resistance vs. Supply Voltage
120
116
112
108
104
100 RL=10ohm
96 T=25℃
92
88
2.5 3.0 3.5 4.0 4.5 5.0 5.5
SUPPLY VOLTAGE (V)
Turn-On Rise Time vs. Supply Voltage
1.4
1.2
1.0 85OC
0.8 -40OC
25OC
0.6
0.4
0.2
0.0
2.5
220
200
180
160
140
120
100
80
60
40
20
0
2.5
RL=10ohm
CL=47 uF
3.0 3.5 4.0 4.5 5.0
SUPPLY VOLTAGE (V)
On-Current vs. Supply Voltage
5.5
25OC
-40OC
85OC
3.0 3.5 4.0 4.5 5.0 5.5
SUPPLY VOLTAGE (V)
160
150
140
130
120
110
100
90
80
70
60
- 40
On-Resistance vs. Temperature
VSUPPLY =5V
VSUPPLY=3.3V
RL=10ohm
- 20 0 20 40 60 80 100
TEMPERATURE (O C )
Turn-On Rise Time vs. Temperature
1.4
1.2
VSUPPLY =5V
1.0
0.8
0.6 VSUPPLY=3.3V
0.4
0.2
0.0
-40
-20
RL=10ohm
CL=47uF
0 20 40 60
TEMPERATURE (OC)
80 100
200
180
160
140
120
100
80
60
40
20
0
-40
On-Current vs. Temperature
VSUPPLY=5V
VSUPPLY =3.3V
-20 0
20 40 60 80
TEMPERATUREO(C)
100
AP1212 Rev. 2
5 of 12
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
5 Page Marking Information
AP1212
DUAL USB HIGH-SIDE POWER SWITCH
SOP-8L
(Top View)
85
Logo
Part Number
AP12 12 X
YY WW X X
1
SOP-8L
4
Enable Type
H : Active High
L : Active Low
L : Lead Free
G : Green
ID code: internal
Xth week: 01~52
Year: "01" =2001
"02" =2002
Device
AP1212XS
Package
SOP-8L
Identification Code
AP1212
Package Information
Package Type: SOP-8L
7°~9°
1.27typ
0.3/0.5
4.80/5.30
0.38/1.27
Detail "A"
Gauge Plane
Seating Plane
0.35max. 45°
7°~9°
Detail "A"
3.70/4.10
AP1212 Rev. 2
11 of 12
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
11 Page |
Páginas | Total 12 Páginas | |
PDF Descargar | [ Datasheet AP1212.PDF ] |
Número de pieza | Descripción | Fabricantes |
AP1210MP | 2.5A SINK/SOURCE BUS TERMINATION REGULATOR | Advanced Power Electronics |
AP1212 | Dual USB High-Side Power Switch | ETC |
AP1212 | DUAL USB HIGH-SIDE POWER SWITCH | Diodes Incorporated |
AP1212 | Dual USB High-Side Power Switch | Anachip |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |