|
|
PDF MC74VHCT14A Data sheet ( Hoja de datos )
| Número de pieza | MC74VHCT14A | |
| Descripción | Hex Schmitt Inverter | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MC74VHCT14A (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
MC74VHCT14A
Hex Schmitt Inverter
The MC74VHCT14A is an advanced high speed CMOS Schmitt
inverter fabricated with silicon gate CMOS technology. It achieves
high speed operation similar to equivalent Bipolar Schottky TTL
while maintaining CMOS low power dissipation.
Pin configuration and function are the same as the
MC74VHCT04A, but the inputs have hysteresis and, with its Schmitt
trigger function, the VHCT14A can be used as a line receiver which
will receive slow input signals.
The VHCT inputs are compatible with TTL levels. This device can
be used as a level converter for interfacing 3.3 V to 5.0 V, because it
has full 5.0 V CMOS level output swings.
The VHCT14A input structures provide protection when voltages
between 0 V and 5.5 V are applied, regardless of the supply voltage.
The output structures also provide protection when VCC = 0 V. These
input and output structures help prevent device destruction caused by
supply voltage − input/output voltage mismatch, battery backup, hot
insertion, etc.
The internal circuit is composed of three stages, including a buffer
output which provides high noise immunity and stable output. The
inputs tolerate voltages up to 7.0 V, allowing the interface of 5.0 V
systems to 3.0 V systems.
Features
• High Speed: tPD = 5.5 ns (Typ) at VCC = 5.0 V
www.DataSheet4U.com
• Low Power Dissipation: ICC = 2.0 mA (Max) at TA = 25°C
• TTL−Compatible Inputs: VIL = 0.8 V; VIH = 2.0 V
• Power Down Protection Provided on Inputs
• Balanced Propagation Delays
• Designed for 2.0 V to 5.5 V Operating Range
• Low Noise: VOLP = 0.8 V (Max)
• Pin and Function Compatible with Other Standard Logic Families
• Chip Complexity: 60 FETs or 15 Equivalent Gates
• Pb−Free Packages are Available*
http://onsemi.com
MARKING
DIAGRAMS
14
SOIC−14
VHCT14AG
1
D SUFFIX
CASE 751A
AWLYWW
1
14
TSSOP−14
VHCT
DT SUFFIX
14A
1
CASE 948G
ALYWG
G
1
14
1
SOEIAJ−14
M SUFFIX
CASE 965
74VHCT14
ALYWG
1
A = Assembly Location
WL, L = Wafer Lot
Y, YY = Year
WW, W = Work Week
G or G = Pb−Free Package
(Note: Microdot may be in either location)
FUNCTION TABLE
Inputs
Outputs
AY
LH
HL
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2006
April, 2006 − Rev. 4
1
Publication Order Number:
MC74VHCT14A/D
1 page  
MC74VHCT14A
PACKAGE DIMENSIONS
−A−
14
8
SOIC−14
D SUFFIX
CASE 751A−03
ISSUE G
1
G
−B− P 7 PL
0.25 (0.010) M B M
7
C R X 45 _
−T−
SEATING
PLANE
D 14 PL
K
0.25 (0.010) M T B S A S
M
F
J
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.127
(0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
MILLIMETERS INCHES
DIM MIN MAX MIN MAX
A 8.55 8.75 0.337 0.344
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC
0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0_ 7_ 0_ 7_
P 5.80 6.20 0.228 0.244
R 0.25 0.50 0.010 0.019
TSSOP−14
CASE 948G−01
ISSUE A
0.15 (0.006) T U S
2X L/2 14
L
PIN 1
IDENT.
1
14X K REF
0.10 (0.004) M T U S V S
N 0.25 (0.010)
8
M
B
−U− N
F
7 DETAIL E
0.15 (0.006) T U S
A
−V−
K
J J1 ÇÇÉÉÇÇÉÉK1ÇÇÉÉ
SECTION N−N
0.10 (0.004)
−T− SEATING
PLANE
D
C
G
H DETAIL E
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
−W−
MILLIMETERS INCHES
DIM MIN MAX MIN MAX
A 4.90 5.10 0.193 0.200
B 4.30 4.50 0.169 0.177
C −−− 1.20 −−− 0.047
D 0.05 0.15 0.002 0.006
F 0.50 0.75 0.020 0.030
G 0.65 BSC 0.026 BSC
H 0.50 0.60 0.020 0.024
J 0.09 0.20 0.004 0.008
J1 0.09 0.16 0.004 0.006
K 0.19 0.30 0.007 0.012
K1 0.19 0.25 0.007 0.010
L 6.40 BSC 0.252 BSC
M 0_ 8_ 0_ 8_
http://onsemi.com
5
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet MC74VHCT14A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MC74VHCT14A | Hex Schmitt Inverter |  Motorola Semiconductors |
| MC74VHCT14A | Hex Schmitt Inverter | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |