|
|
PDF MBRP20060CT Data sheet ( Hoja de datos )
| Número de pieza | MBRP20060CT | |
| Descripción | POWERTAP II SWITCHMODE Power Rectifier | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MBRP20060CT (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
MBRP20060CT
Preferred Device
POWERTAPt II
SWITCHMODEt
Power Rectifier
These state−of−the−art devices use the Schottky Barrier principle
with a platinum barrier metal.
Features
• Dual Diode Construction − May Be Paralleled for Higher Current
Output
• Guardring for Stress Protection
• Low Forward Voltage
• 150°C Operating Junction Temperature
• Pb−Free Package is Available*
Mechanical Characteristics:
• Case: Epoxy, Molded with metal heatsink base
• Weight: 80 Grams (Approximately)
• Finish: All External Surfaces Corrosion Resistant
• Top Terminal Torque: 25−40 lb−in max
• Base Plate Torques: See procedure given in the Package Outline
Section
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
60
V
Average Rectified Forward Current
(Rated VR, TC = 140°C)
Per Leg
Per Device
IF(AV)
100
200
A
Peak Repetitive Forward Current,
(Rated VR, Square Wave,
20 kHz, TC = 140°C)
Per Leg
IFRM
200
A
Non−Repetitive Peak Surge Current
(Surge Applied at Rated Load Conditions
Halfwave, Single Phase, 60 Hz)
IFSM
1500
A
Peak Repetitive Reverse Current
IRRM
(2.0 ms, 1.0 kHz)
Per Leg
2.0
A
Storage Temperature Range
Operating Junction Temperature
Voltage Rate of Change (Rated VR)
Tstg
TJ
dv/dt
−55 to +150
−55 to +150
10,000
°C
°C
V/ms
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2006
September, 2006 − Rev. 4
1
http://onsemi.com
SCHOTTKY
BARRIER RECTIFIER
200 AMPERES, 60 VOLTS
1
3
2
2
1
3
POWERTAP II
CASE 357C
PLASTIC
MARKING DIAGRAM
MCC
AYYWWG
B20060T
B20060T
MCC
A
YY
WW
G
= Specific Device Code
= Mold Compound Code
= Assembly Location
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
Device
MBRP20060CT
MBRP20060CTG
Package
POWERTAP II
POWERTAP II
(Pb−Free)
Shipping
25 Units/Tray
25 Units/Tray
Preferred devices are recommended choices for future use
and best overall value.
Publication Order Number:
MBRP20060CT/D
1 page  
MBRP20060CT
MAXIMUM MECHANICAL RATINGS
Terminal Penetration:
Terminal Torque:
Mounting Torque —
Outside Holes:
Mounting Torque —
Center Hole:
Seating Plane
Flatness
0.235 max
25−40 in-lb max
30−40 in-lb max
8−10 in-lb max
1 mil per in.
(between mounting holes)
POWERTAP MECHANICAL DATA
APPLIES OVER OPERATING TEMPERATURE
2″
Vertical Pull
250 lbs. max
2 in. Lever Pull
50 lbs. max
Note: While the POWERTAP is capable of sustaining these vertical and levered tensions, the intimate contact
Note: between POWERTAP and heat sink may be lost. This could lead to thermal runaway. The use of very
Note: flexible leads is recommended for the anode connections. Use of thermal grease is highly recommended.
MOUNTING PROCEDURE
The POWERTAP package requires special mounting considerations because of the long longitudinal axis of the copper
heat sink. It is important to follow the proper tightening sequence to avoid warping the heat sink, which can reduce thermal
contact between the POWERTAP and heat sink.
STEP 1:
Locate the POWERTAP on the heat sink and
start mounting bolts into the threads by hand
(2 or 3 turns).
2 −3 TURNS
2 −3 TURNS
2 −3 TURNS
POWER
HEAT
TAP
SINK
STEP 2:
Finger tighten the center bolt. The bolt may
catch on the threads of the heat sink so it is
important to make sure the face of the bolt or
washer is in contact with the surface of the
POWERTAP.
STEP 3:
Tighten each of the end bolts between 5 to 10
in-lb.
2 −3 TURNS
FINGER-TIGHT
2 −3 TURNS
POWER
HEAT
TAP
SINK
5 −10 IN-LB
FINGER-TIGHT
5 −10 IN-LB
POWER
HEAT
TAP
SINK
STEP 4:
Tighten the center bolt between 8 to 10 in-lb.
STEP 5:
Finally, tighten the end bolts between 30 to 40
in-lb.
5 −10 IN-LB
8 −10 IN-LB
5 −10 IN-LB
POWER
HEAT
TAP
SINK
30 −40 IN-LB
8 −10 IN-LB
30 −40 IN-LB
POWER
HEAT
TAP
SINK
http://onsemi.com
5
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet MBRP20060CT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MBRP20060CT | SCHOTTKY BARRIER RECTIFIER 200 AMPERES 60 VOLT |  Motorola Semiconductors |
| MBRP20060CT | POWERTAP II SWITCHMODE Power Rectifier | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |