|
|
Número de pieza | CS8120 | |
Descripción | Linear Regulator | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CS8120 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
No Preview Available ! www.DataSheet4U.com
CS8120
5.0 V, 300 mA Linear
Regulator with RESET
and ENABLE
The CS8120 is a 5.0 V, 300 mA precision linear regulator with two
microprocessor compatible control functions and protection circuitry
included on chip. The composite NPN−PNP output pass transistor
assures a lower dropout voltage (1.0 V @ 200 mA) without requiring
excessive supply current (2.5 mA).
The CS8120’s two logic control functions make this regulator well
suited to applications requiring microprocessor−based control at the
board or module level. ENABLE controls the output stage. A high
voltage (> 2.9 V) on the ENABLE lead turns off the regulator’s pass
transistor and sends the IC into Sleep mode where it draws only 250 mA.
The RESET function sends a RESET signal when the IC is powering up
or whenever the output voltage moves out of regulation. The RESET
signal is valid down to VOUT = 1.0 V.
The CS8120 design optimizes supply rejection by switching the
internal bandgap reference from the supply input to the regulator
output as soon as the nominal output voltage is achieved. Additional
on chip filtering enhances rejection of high frequency transients on all
external leads.
The CS8120 is fault protected against short circuit, over voltage and
thermal runaway conditions.
Features
• 5.0 V ±4.0% Output Voltage 300 mA
• Low Dropout Voltage (1.0 V @ 150 mA)
• Low Quiescent Current (2.5 mA @ IOUT = 150 mA)
• mP Compatible Control Functions
− RESET
− ENABLE
• Low Current Sleep Mode
− IQ = 250 mA
• Fault Protection
− Thermal Shutdown
− Short Circuit
− 60 V Load Dump
http://onsemi.com
1
5
1
TO−220−5
T SUFFIX
CASE 314D
TO−220−5
TVA SUFFIX
CASE 314K
1
5
1
5
8
1
14
1
TO−220−5
THA SUFFIX
CASE 314A
D2PAK−5
DP SUFFIX
CASE 936AC
DIP−8
N SUFFIX
CASE 626
SO−14
D SUFFIX
CASE 751A
© Semiconductor Components Industries, LLC, 2004
January, 2004 − Rev. 8
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 10 of this data sheet.
1 Publication Order Number:
CS8120/D
1 page CS8120
TYPICAL PERFORMANCE CHARACTERISTICS
50
VIN = 7 to 25 V
40
1.4
1.2
30 1.0
20
25°C
0.8
125°C
0.6
10
−40°C
0.4
0
0.2
−10
0
50 100 150 200 250 300 350 400 450 500
IOUT (mA)
Figure 4. Line Regulation vs. Output
Current Over Temperature
0.0
0
3.5
VIN = 14 V
3.0
−40°C
2.5
25°C
5.5
5
4
2.0
125°C
1.5
3
2
1.0
1
0.5
−40°C
25°C
125°C
50 100 150 200 250 300 350
Output Current (mA)
Figure 5. Dropout Voltage vs. Output
Current Over Temperature
22
20
VOUT
16
12
IQ
8
4
0.0
0
50 100 150 200 250 300
Output Current (mA)
Figure 6. Quiescent Current vs. Output
Current Over Temperature
350
0
0
2 468
Supply Voltage (V)
Figure 7. Output Voltage and Supply
Current vs. Input Voltage
0
10
2000
1800
1600
1400
1200
1000
800
600
400
200
VIN = 5.0 V
0
1 5 10 15 20 25 30 35 40
Reset Output Current (mA)
Figure 8. RESET Output Voltage vs.
Output Voltage
http://onsemi.com
5
5 Page CS8120
PACKAGE DIMENSIONS
−Q− B
U
K 12345
A
TO−220−5
T SUFFIX
CASE 314D−04
ISSUE E
−T−
SEATING
PLANE
C
E
L
D 5 PL
G
0.356 (0.014) M T Q M
J
H
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 10.92 (0.043) MAXIMUM.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.572 0.613 14.529 15.570
B 0.390 0.415 9.906 10.541
C 0.170 0.180 4.318 4.572
D 0.025 0.038 0.635 0.965
E 0.048 0.055 1.219 1.397
G 0.067 BSC
1.702 BSC
H 0.087 0.112 2.210 2.845
J 0.015 0.025 0.381 0.635
K 0.990 1.045 25.146 26.543
L 0.320 0.365 8.128 9.271
Q 0.140 0.153 3.556 3.886
U 0.105 0.117 2.667 2.972
TO−220−5
TVA SUFFIX
CASE 314K−01
ISSUE O
B
−Q−
U
12345
A
D 5 PL
G
0.356 (0.014) M T Q M
−T−
SEATING
PLANE
C
E
W
L
M
J
F
K
S
R
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D, INCLUDING PROTRUSION, SHALL
NOT EXCEED 10.92 (0.043) MAXIMUM.
INCHES
DIM MIN MAX
A 0.560 0.590
B 0.385 0.415
C 0.160 0.190
D 0.027 0.037
E 0.045 0.055
F 0.530 0.545
G 0.067 BSC
J 0.014 0.022
K 0.785 0.800
L 0.321 0.337
M 0.063 0.078
Q 0.146 0.156
R 0.271 0.321
S 0.146 0.196
U 0.460 0.475
W 5_
MILLIMETERS
MIN MAX
14.22 14.99
9.78 10.54
4.06 4.83
0.69 0.94
1.14 1.40
13.46 13.84
1.70 BSC
0.36 0.56
19.94 20.32
8.15 8.56
1.60 1.98
3.71 3.96
6.88 8.15
3.71 4.98
11.68 12.07
5_
http://onsemi.com
11
11 Page |
Páginas | Total 14 Páginas | |
PDF Descargar | [ Datasheet CS8120.PDF ] |
Número de pieza | Descripción | Fabricantes |
CS8120 | 5V/ 300mA Linear Regulator with and ENABLE RESET | Cherry Semiconductor Corporation |
CS8120 | Linear Regulator | ON Semiconductor |
CS8120YD14 | 5V/ 300mA Linear Regulator with and ENABLE RESET | Cherry Semiconductor Corporation |
CS8120YDP5 | 5V/ 300mA Linear Regulator with and ENABLE RESET | Cherry Semiconductor Corporation |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |