|
|
PDF LT1ED90A Data sheet ( Hoja de datos )
| Número de pieza | LT1ED90A | |
| Descripción | DEVICE SPECIFICATION FOR Light Emitting Diode | |
| Fabricantes | Sharp Electrionic Components | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LT1ED90A (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
PREPARED BY:
JJ&,~
APPROVED BY:
DATE:
-2 ; 97
DATE:
//
s-a -y--3-1--‘I-&-_-j.&._:,,:_-f:i-.-:ii -I :,a.-- ;:,+;SPEC.No.
-_ti~~~t34-.
ELECTROMC COMPONENTS GROUP
SHARP CORPORATION
SPECIFICATION
PALa
REPRESENTATIVE DMSION:
Opto-Electronic Devices Division
DEVICE SPECIFICATION FOR
Light Emitting Diode
MODEL No.
LTlED9OA
1. These specification sheets include materials protected under the copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2. When using this produ& please observe the absolute maximm ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damageresuking from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This products is designed for use in the following application areas;
r * OA equipment * Audio visual equipment * Home appliance
L* Telecommunication equipment (Terminal)
* Tooling machines * Computers
* Measuring equipment
1
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as W-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in fimction and precision, such as ;
r * Transportation control and safety equipment (aircra& train, automobile etc.)
* Tra& signals * Gas leakage sensor breakers * Rescue and security equipment
1 * Other safety equipment
1
(3) Please do not use this product for equipment which require extremely high reliability
and safety in fLnction and precision, such as ;
r * Spaceequipment * Telecommunication equipment (for trunk lines)
L * Nuclear power control equipment l Medical equipment
I
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult ,tith a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE:
BY:
DATE:
AC. / J
PRESENTED BY.
4 Al . &,I
M.Katoh,
Department General iManager of
Engineering Dept.,111
Opto-Electronic Devices Division
Electronic Components Group
SHARP CORPORXTION
/ f7yy
1 page  
3-3. D&g Curve(Yellow-greenandRed)
FotwardCurrenDt entingCurve
i ---.- -.__
DG-992004
*--._____
PeakForwarCdurentDemtingCurve
D&3/99
-25 0 25 50 7585100 125
AmbientTemperatuTrea(“c)
PeakForwardCurrentvs.Duty Ratio
(Ta=25”C)
0 25 50 75g5100 125
AmbientTemperaturTefl)
DuryRAo
.
5 Page 
6-l-3 .Tapingspecification
(1) Leadtape:
DG-992004
Deem99
MbDEL No.
PAGE
z LTlEDSOA
j 3 4 - .I
’ -IQ8443
--- ‘.
Pull ,,,I-->
.
__
End 000000
0000000000
q ICIU~ q mnn
170
Empty -I- Stuffed A-
Empty
I-Leading
’ 10 pitch or ‘more
40-50 pitch
(2) Covertapestrengthagainstpeeling:P=O.l-O8N( 0 =lO’or less)
Begirming
Cover tape
c ’ - ‘yape speed : Smm/s
<- Forward
Carrier
tape
(3) Tapestrengthagainstbending:
Theradiusof bendingcircle shouldbe3Ommor more.
Ifit is lessthan3Ommt,he cover may peel.
(4) Jointingof tape:
Thereshouldnot bejoint of covertapeor carriertape.
(5) Quantityperreel:
Average 3,OOOpcsp.erreel
(6) Massperproducts: Average 0.02g1product
(7)Massperpacking:
Average 150gI packing
(8) Others: @ Thereshouldnot bemissingabovecontinuousthreeproducts.
@ Productsshouldbeeasilytakenout
@ Productsshouldnot beattachedto thecovertapeat peeling.
6-2.Packingspecification
6-2-1.Dampproofpackage
In otherto avoidthe absorptionof humidity in transportandstorage,the devices arepacked
in aluminumsleeve.
Lab.31
6-2-2.Strage conditions
Temperature: 5 to 30°C Humidity : lessthan6O%RH
6-2-3.Trement after opening
(1) Pleasemakea solderingwithin 15daysafter openingunderfollowing condition;
Temperature: 5 to 30°C Humidity : lessthan6O%RH
(2) In casethe devicesarenot usedfor a long tuneafter opening,thestoragein dry box is recommendable.
Or it is betterto repackthe deviceswith a desiccativeby thesealerandputthemin thesomestorage
conditions as6-2-2.Thenthey shouldbeusedwithin 2 weeks.
(3) Pleasemakea solderingafter a follewing bakingtreatmentif unusedtermshouldbeover the conditionsof (2)
*Recommendablceonditions:
0 in taping
Temprature:6O’C to 6Y’C,Time:j6 to 38 hours
0 in individual (on PWB or metallic tray)
Tempnture: IOO’C to 13Oc .Time:Z to 3 hours
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet LT1ED90A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LT1ED90A | DEVICE SPECIFICATION FOR Light Emitting Diode | Sharp Electrionic Components |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |