|
|
PDF TA7713P Data sheet ( Hoja de datos )
| Número de pieza | TA7713P | |
| Descripción | 3 PHASE BI-DIRECTIONAL TYPE MOTOR CONTROL IC | |
| Fabricantes | Toshiba Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TA7713P (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
TA7713P
TOSHIBA BIPOLAR LINEAR INTEGRATED CIRCUIT SILICON MONOLITHIC
TA7713P
3 PHASE BI−DIRECTIONAL TYPE MOTOR CONTROL IC
FEATURES
l FG is not required.
(System for obtaining rotation signal through position
sensing)
l Stop function is provided (Stop speed is selectable.)
l Gain of position sensing circuit is high, and hysteresis is
provided.
l Rotation signal output is provided. (Frequency signal of three
times the position sensing output (Hall sensor output) can be
obtained.)
l External transistor type.
BLOCK DIAGRAM
Weight: 2.25 g (Typ.)
1 2001-06-13
1 page  
TA7713P
(2) Stopping function
For stopping the motor, it is the simplest way to stop the inertia through the friction after turning off the
motor driving power supply.
However, since too much time is required for stopping the motor having a large inertia, this method is not
suitable to the video disk or audio disk player which requires the disk changed in a short time.
In this case, the motor is changed over to the reverse torque state at the same with the input of the stop signal,
and the brake is applied keeping the state of normal rotation with reverse torque as an usual method.
In this method, however, reverse runaway is liable to occur unless the reduction of rotation is detected through
a certain measure to stop the reverse torque state at an appropriate time.
(For example, PLL motor controller TC9142AP is provided with the circuit by which the reverse rotation signal
is output at the same time with the stop signal input, and the reduction of rotation speed in this reverse torque
state is detected by FG signal to disconnect the reverse rotation signal when the rotation speed reduced down
to 1 / 8 the initial speed.)
In case of the motor of high rotation speed and large inertia like the motor for video disk, to perform the quick
braking operation, it is necessary to keep this condition of the forward rotation with reverse torque until just
before the motor stops in order to reduce the inertia stopping time to the minimum through the friction force.
For this purpose, in TA7713P, the state of forward rotation with reverse torque is kept continued until the
motor stops and either of three position sensing signals detects the reverse rotation with the built−in reverse
sensing circuit.
(In case of application of TA7713P, there is no problem in the optical system, however, it is of course necessary
to put the sensor apart from the disk at the same time with the stop signal input or before the reverse rotation
start in VHD CED system.)
At this time, the state of the reverse rotation is max. 60° in electrical angle.
Furthermore, in order to remove the inertia due to this reverse rotation, the inside monostable multi−vibrator
generates the time normal torque determined by the state of C2, R2 and pin (10) to turn out the
inertia−stopped state afterwards.
By means of these functions, the motor can be stopped in 5~8 seconde with the optical system of high rotation
speed and in 2~3 seconds with VHD CED system.
5 2001-06-13
5 Page 
TEST CIRCUIT 2
TA7713P
Hall AMP. Input
Check input sensitivity and
input hysteresis with ±20 mV
by means of confirming that
leak current and saturation
voltage described below can be
measured.
Va
2.52 V
2.48 V
2.48 V
INPUT CONDITION
Vb Vc RUN
2.48 V 2.48 V VIN R (L)
2.52 V 2.48 V
―
2.48 V 2.52 V
―
F/R
VIN C (L)
―
―
LEAK: Measurement of leak current
SAT: Measurement of saturation voltage
La+
LEAK
SAT
―
La−
SAT
MEALSbU+REMENLTb−ITEM
LEAK LEAK
Lc+
SAT
LEAK
―
SAT LEAK
― SAT ―
―
Lc−
LEAK
―
SAT
11 2001-06-13
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet TA7713P.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TA7713P | 3 PHASE BI-DIRECTIONAL TYPE MOTOR CONTROL IC | Toshiba Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |