|
|
PDF MC74HC75 Data sheet ( Hoja de datos )
| Número de pieza | MC74HC75 | |
| Descripción | Dual 2-Bit Transparent Latch | |
| Fabricantes | Motorola Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MC74HC75 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Dual 2-Bit Transparent Latch
High–Performance Silicon–Gate CMOS
The MC74HC75 is identical in pinout to the LS75. The device inputs are
compatible with standard CMOS outputs; with pullup resistors, they are
compatible with LSTTL outputs.
This device consists of two independent 2–bit transparent latches. Each
latch stores the input data while Latch Enable is at a logic low. The outputs
follow the data inputs when Latch Enable is at a logic high.
• Output Drive Capability: 10 LSTTL Loads
• Outputs Directly Interface to CMOS, NMOS, and TTL
• Operating Voltage Range: 2 to 6 V
• Low Input Current: 1 µA
• High Noise Immunity Characteristic of CMOS Devices
• In Compliance with the Requirements Defined by JEDEC Standard
No. 7A
• Chip Complexity: 80 FETs or 20 Equivalent Gates
LOGIC DIAGRAM
DATA
INPUTS
2, 6
D0
3, 7
D1
2–BIT
TRANSPARENT
LATCH
16, 10 Q0
1, 11 Q0
15, 9 Q1
14, 8 Q1
LATCH 13, 4
ENABLE
PIN 5 = VCC
PIN 12 = GND
MC74HC75
16
1
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
16
1
D SUFFIX
SOIC PACKAGE
CASE 751B–05
ORDERING INFORMATION
MC74HCXXN
MC74HCXXD
Plastic
SOIC
PIN ASSIGNMENT
Q0a 1
D0a 2
D1a 3
LEb 4
VCC 5
D0b 6
D1b 7
Q1b 8
16 Q0a
15 Q1a
14 Q1a
13 LEa
12 GND
11 Q0b
10 Q0b
9 Q1b
FUNCTION TABLE
Inputs
Latch
D Enable
LH
HH
XL
Outputs
QQ
LH
HL
Q0 Q0
X = don’t care
Q0 = latched data
10/95
© Motorola, Inc. 1995
1 REV 6
1 page  
–A
–
16
1
H
G
OUTLINE DIMENSIONS
9
B
8
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
ISSUE R
FC
S
–T
–
SEATING
PLANE
K
J
D 16 PL
0.25 (0.010) M T A M
L
M
MC74HC75
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.070 1.02 1.77
G
0.100 BSC
2.54 BSC
H
0.050 BSC
1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M
0° 10°
0° 10°
S 0.020 0.040 0.51 1.01
–A
–
16
1
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
ISSUE J
9
–B
–
8
P 8 PL
0.25 (0.010) M
BM
–T
SEAT–ING
PLANE
G
K
C
D 16 PL
0.25 (0.010) M T B S A S
M
R X 45°
F
J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
MILLIMETERS
INCHES
DIM MIN MAX MIN MAX
A 9.80 10.00 0.386 0.393
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G
1.27 BSC
0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0° 7° 0° 7°
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [email protected] –TOUCHTONE (602) 244–6609
INTERNET: http://Design–NET.com
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
High–Speed CMOS Logic Data
DL129 — Rev 6
◊ CODELINE
5
*MC74HC75/D*MC74HC75/D
MOTOROLA
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet MC74HC75.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MC74HC7266 | Quad 2-Input Exclusive NOR Gate | Motorola Semiconductors |
| MC74HC7266A | Quad 2-Input Exclusive NOR Gate | Motorola Semiconductors |
| MC74HC73 | Dual J-K Flip-Flop with Reset | Motorola Semiconductors |
| MC74HC73A | Dual J-K Flip-Flop |  ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |