PDF MTP2P50E Data sheet ( Hoja de datos )

Número de pieza	MTP2P50E
Descripción	TMOS POWER FET 2.0 AMPERES 500 VOLTS RDS
Fabricantes	Motorola Semiconductors
Logotipo
Hay una vista previa y un enlace de descarga de MTP2P50E (archivo pdf) en la parte inferior de esta página. Total 8 Páginas
No Preview Available ! MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MTP2P50E/D ™Designer's Data Sheet TMOS E-FET.™ Power Field Effect Transistor P–Channel Enhancement–Mode Silicon Gate This high voltage MOSFET uses an advanced termination scheme to provide enhanced voltage–blocking capability without degrading performance over time. In addition, this advanced TMOS E–FET is designed to withstand high energy in the avalanche and commutation modes. The new energy efficient design also offers a drain–to–source diode with a fast recovery time. Designed for high voltage, high speed switching applications in power supplies, converters and PWM motor controls, these devices are particularly well suited for bridge circuits where diode speed and commutating safe operating areas are critical and offer additional safety margin against unexpected voltage transients. • Robust High Voltage Termination • Avalanche Energy Specified • Source–to–Drain Diode Recovery Time Comparable to a Discrete Fast Recovery Diode • Diode is Characterized for Use in Bridge Circuits • IDSS and VDS(on) Specified at Elevated Temperature ® D MTP2P50E Motorola Preferred Device TMOS POWER FET 2.0 AMPERES 500 VOLTS RDS(on) = 6.0 OHM MAXIMUM RATINGS (TC = 25°C unless otherwise noted) Rating G CASE 221A–06, Style 5 TO–220AB S Symbol Value Unit Drain–Source Voltage Drain–Gate Voltage (RGS = 1.0 MΩ) Gate–Source Voltage — Continuous Gate–Source Voltage — Non–Repetitive (tp ≤ 10 ms) VDSS VDGR VGS VGSM 500 Vdc 500 Vdc ± 20 Vdc ± 40 Vpk Drain Current — Continuous Drain Current — Continuous @ 100°C Drain Current — Single Pulse (tp ≤ 10 µs) Total Power Dissipation Derate above 25°C ID 2.0 Adc ID 1.6 IDM 6.0 Apk PD 75 Watts 0.6 W/°C Operating and Storage Temperature Range TJ, Tstg – 55 to 150 °C Single Pulse Drain–to–Source Avalanche Energy — Starting TJ = 25°C (VDD = 100 Vdc, VGS = 10 Vdc, IL = 4.0 Apk, L = 10 mH, RG = 25 Ω) EAS 80 mJ Thermal Resistance — Junction to Case Thermal Resistance — Junction to Ambient RθJC RθJA 1.67 °C/W 62.5 Maximum Lead Temperature for Soldering Purposes, 1/8″ from case for 10 seconds TL 260 °C Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit curves — representing boundaries on device characteristics — are given to facilitate “worst case” design. E–FET and Designer’s are trademarks of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc. Preferred devices are Motorola recommended choices for future use and best overall value. REV 1 © MMoototororloa,laIncT.M19O95S Power MOSFET Transistor Device Data 1 1 page 12 10 8 Q1 6 4 QT Q2 300 250 VGS 200 ID = 2 A TJ = 25°C 150 100 2 50 Q3 VDS 00 02 4 6 8 10 12 14 16 18 20 QT, TOTAL CHARGE (nC) Figure 8. Gate–To–Source and Drain–To–Source Voltage versus Total Charge 1000 VDD = 250 V ID = 2 A VGS = 10 V TJ = 25°C MTP2P50E 100 td(off) tf tr td(on) 10 1 10 100 RG, GATE RESISTANCE (OHMS) Figure 9. Resistive Switching Time Variation versus Gate Resistance DRAIN–TO–SOURCE DIODE CHARACTERISTICS 2 VGS = 0 V 1.6 TJ = 25°C 1.2 0.8 0.4 0 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 VSD, SOURCE–TO–DRAIN VOLTAGE (VOLTS) Figure 10. Diode Forward Voltage versus Current SAFE OPERATING AREA The Forward Biased Safe Operating Area curves define the maximum simultaneous drain–to–source voltage and drain current that a transistor can handle safely when it is for- ward biased. Curves are based upon maximum peak junc- tion temperature and a case temperature (TC) of 25°C. Peak repetitive pulsed power limits are determined by using the thermal response data in conjunction with the procedures discussed in AN569, “Transient Thermal Resistance–General Data and Its Use.” Switching between the off–state and the on–state may tra- verse any load line provided neither rated peak current (IDM) nor rated voltage (VDSS) is exceeded and the transition time (tr,tf) do not exceed 10 µs. In addition the total power aver- aged over a complete switching cycle must not exceed (TJ(MAX) – TC)/(RθJC). A Power MOSFET designated E–FET can be safely used in switching circuits with unclamped inductive loads. For reli- able operation, the stored energy from circuit inductance dis- sipated in the transistor while in avalanche must be less than the rated limit and adjusted for operating conditions differing from those specified. Although industry practice is to rate in terms of energy, avalanche energy capability is not a con- stant. The energy rating decreases non–linearly with an in- crease of peak current in avalanche and peak junction temperature. Although many E–FETs can withstand the stress of drain– to–source avalanche at currents up to rated pulsed current (IDM), the energy rating is specified at rated continuous cur- rent (ID), in accordance with industry custom. The energy rat- ing must be derated for temperature as shown in the accompanying graph (Figure 12). Maximum energy at cur- rents below rated continuous ID can safely be assumed to equal the values indicated. Motorola TMOS Power MOSFET Transistor Device Data 5 5 Page

Páginas	Total 8 Páginas
PDF Descargar	[ Datasheet MTP2P50E.PDF ]

Hoja de datos destacado

Número de pieza	Descripción	Fabricantes
MTP2P50E	TMOS POWER FET 2.0 AMPERES 500 VOLTS RDS	Motorola Semiconductors
MTP2P50EG	Power MOSFET ( Transistor )	ON Semiconductor

Número de pieza	Descripción	Fabricantes
SLA6805M	High Voltage 3 phase Motor Driver IC.	Sanken
SDC1742	12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.	Analog Devices

DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.

DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar