|
|
Número de pieza | SP4446EK | |
Descripción | High Output Voltage Boost Regulator LCD Bias Regulator | |
Fabricantes | Sipex | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SP4446EK (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! ®
PRELIMINARY
SP4446
High Output Voltage Boost Regulator
LCD Bias Regulator
FEATURES
■ High Output Voltage: Up to 30V
■ High Efficiency
■ Low Quiescent Current: ~20uA
■ Miniature Package: (5-lead SOT-23)
■ Single Battery Cell Operation
■ Programmable Output Voltage
■ 1Ω Switch (150mV at 150mA)
APPLICATIONS
■ LCD Bias
■ Tuner Pin Voltage
■ White LED Driver
■ High Voltage Bias
■ Digital Cameras
■ Cell Phone
■ Battery Backup
■ Handheld Computers
VIN SHDN
54
SP4446
5 Pin SOT-23
1 23
SW
GND
FB
Now Available in Lead Free Packaging
DESCRIPTION
The SP4446 is a micro power Boost Regualtor in a 5-lead SOT-23 package. It is a current limited,
fixed off time regulator configured for use in boost mode applications. The operating voltage can
be less than 3V and is capable of generating voltages as high as 30 Volts.
The SP4446 is to be supplied in a SOT-23-5 and permits the construction of complete regulators
that occupy < 0.2 square inches of board space.
TYPICAL APPLICATION SCHEMATIC
VIN
2 to 7V
C1
4.7µF
L1 D1
10µH
VIN SW
SP4446
SHDN GND
FB
R1
R2
High
Voltage Output
C2
2.2 µF
Rev. 7/14/03
SP4446 High Output Voltage Boost Regualtor, LCD Bias Regulator
1
© Copyright 2003 Sipex Corporation
1 page APPLICATION INFORMAMTION: Continued
The formula and table for the resistor selection
are shown below:
will be slightly sacrificed because of the satura-
tion voltage and base current of the PNP transistor.
R1 =( VOUT - 1 ) • R2
1.22
Table 3. Divider Resistor Selection
VOUT (V)
12
15
18
20
30
R1 (Ω)
1M
1M
1M
1M
1M
R2 (Ω)
113K
88.7K
73.2K
64.9K
42.2K
Layout Consideration
Both the input capacitor and the output capacitor
should be placed as close as possible to the IC.
This can reduce the copper trace resistance which
directly effects the input and output ripples. The
feedback resistor network should be kept close to
the FB pin to minimize copper trace connections
that can inject noise into the system. The ground
connection for the feedback resistor network should
connect directly to the GND pin or to an analog
ground plane that is tied directly to the GND pin.
The inductor and the schottky diode should be
placed as close as possible to the switch pin to
minimize the noise coupling to the other circuits,
especially the feedback network.
Load Disconnect in Shutdown
When SP4446 was shut down, the load is still
connected to the input. In applications that re-
quire output isolation during shutdown, an ex-
ternalPNPtransistor(forexample MMBT2907A)
can be added as shown in Figure 20. When the
SP4446 is active, the voltage set at the emitter of
the transistor exceeds the input voltage, forcing
the transistor into the saturation region. When
the SP4446 is shut down, the input voltage
exceeds the emitter voltage, thus the transistor
becomes inactive and provides high-impedance
isolation between the input and load. Efficiency
R3
154K
VIN
L1
10uH
DS Q1
MMBT2907A
C1
4.7uF
U1
5
VIN
1
SW
R1
1M
SP4446
4 SHDN
FB 3
1.22V
GND
R2
64.9K
2
C2
47pF
VOUT
20V
C3
2.2uF
Fig. 20. Load Disconnect in Shutdown
PIN Diode Driver
The SP4446 can be used as PIN diode driver as
shown in Fig. 21. Two Resistors (R1=1MΩ,
R2=42.2KΩ) are used to program the output volt-
age to be 30V. When input voltage is 3.3V or 5V,
it can supply a maximum current of 3mA and 5mA
to the load.
VIN
3.3V or 5V
Murata LQH32CN100K21
L1 10uH 0.3A
DS
MBR0530
C1
4.7uF
U1
5
VIN
1
SW
R1
1M
SP4446
4 SHDN
FB 3
GND
2
1.22V
R2
42.2K
C2
47pF
30V VOUT
3 to 5 mA
C3
2.2uF
Fig. 21. Pin Diode Driver
Rev. 7/14/03
SP4446 High Output Voltage Boost Regualtor, LCD Bias Regulator
5
© Copyright 2003 Sipex Corporation
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet SP4446EK.PDF ] |
Número de pieza | Descripción | Fabricantes |
SP4446EB | Evaluation Board Manual | Sipex |
SP4446EK | High Output Voltage Boost Regulator LCD Bias Regulator | Sipex |
SP4446EK | Evaluation Board Manual | Sipex |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |