|
|
PDF SP26LV431 Data sheet ( Hoja de datos )
| Número de pieza | SP26LV431 | |
| Descripción | High Speed / +3.3V Quad RS-422 Differential Line Driver | |
| Fabricantes | Sipex | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SP26LV431 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
® Preliminary SP26LV431
High Speed, +3.3V Quad RS-422
Differential Line Driver
■ Quad Differential Line Drivers
■ Compatible with the EIA standard for
RS-422 serial protocol
■ High-Z Output Control
■ At Least 60Mbps Transmission Rates
■ 11ns Typical Driver Propagation Delays
■ Less than 1ns Typical Output Skew
■ Single +3.3V Supply Operation
■ Common Driver Enable Control
■ Compatibility with the industry standard
26LV31
■ Ideal For Use with SP26LV432, Quad
Receivers
DI1 1
16 VCC
D01A
2
15
SP26LV431
DI4
D01B 3
14 D04A
ENABLE 4
13 D04B
D02B 5
12 ENABLE
D02A 6
11 D03B
DI2 7
10 D03A
GND 8
9 DI3
DESCRIPTION
The SP26LV431 is a quad differential line driver that meets the specifications of the EIA
standard RS-422 serial protocol. The SP26LV431 features Sipex's BiCMOS process allowing
low power operational characteristics of CMOS technology while meeting all of the demands
of the RS-422 serial protocol over 60Mbps under load. The RS-422 protocol allows up to 10
receivers to be connected to a multipoint bus transmission line. The SP26LV431 features a
driver enable control common to all four drivers that places the output pins in a high impedance
state. Since the cabling can be as long as 4,000 feet, the RS-422 drivers of the SP26LV431
are equipped with a wide common-mode output voltage range to accommodate ground
potential differences.
ENABLE
LOW
ENABLE
HIGH
Input
don't care
Non-
Inverting
A Output
high-Z
Inverting
B Output
high-Z
HIGH don't care
LOW
LOW
HIGH
don't care
LOW
HIGH
HIGH
LOW
ENABLE
ENABLE
TYPICAL APPLICATION CIRCUIT
VCC INPUTS
DI4 DI3 DI2 DI1
DO4A DO4B DO3A DO3B DO2A DO2B DO1A DO1B
GND
OUTPUTS
Rev: A Date: 2/08/04
SP26LV431 High Speed, +3.3V Quad RS-422 Differential Line Driver
1
© Copyright 2004 Sipex Corporationn
1 page  
The SP26LV431 is a low-power quad differen-
tial line driver designed for digital data transmis-
sion meeting the specifications of the EIA stan-
dard RS-422 serial protocol. The SP26LV431
features Sipex's BiCMOS process allowing low
power operational characteristics of CMOS tech-
nology while meeting all of the demands of the
RS-422 serial protocol up to 60Mbps under load
in harsh environments.
The RS-422 standard is ideal for multi-drop
applications and for long-distance communica-
tion. The RS-422 protocol allows up to 10
receivers to be connected to a data bus, making
it an ideal choice for multi-drop applications.
Since the cabling can be as long as 4,000 feet,
RS-422 drivers are equipped with a wide com-
mon mode output range to accommodate ground
potential differences. Because the RS-422 is a
differential interface, data is virtually immune to
noise in the transmission line.
The SP26LV431 accepts TTL or CMOS input
levels and translates these to RS-422 output
levels. The SP26LV431 features active HIGH
and active LOW driver enable controls common
to all four driver channels see Figure 8. A logic
HIGH on the ENABLE pin (pin 4) or a logic
LOW on the ENABLE pin (pin 12) will enable the
differential driver outputs. A logic LOW on the
ENABLE pin (pin 4) and a logic HIGH on the
ENABLE pin (pin 12) will force the driver
outputs into high impedance (high-Z). Refer to
the truth table in Figure 8.
THEORY OF OPERATION
source and sink current capability. All drivers
are internally protected against short circuits on
their outputs. The driver outputs are short-circuit
limited to 150mA. The driver output skew times
are typically 0.8ns.
To minimize reflections, the multipoint bus
transmission line should be terminated at both
ends in its characteristic impedance, and stub
lengths off the main line should be kept as short
as possible.
ENABLE
DATA
ENABLE
*RT
DATA
OUTPUT
*RT is optional although highly
recommended to reduce reflection.
The RS-422 line driver outputs feature high
Figure 7. Two-Wire Balanced System, RS-422
ENABLE
LOW
ENABLE
Input
Non-
Inverting
A Output
Inverting
B Output
HIGH don't care high-Z
high-Z
HIGH don't care
LOW
LOW
HIGH
don't care
LOW
HIGH
HIGH
LOW
Figure 8. Truth Table, Enable / Disable Function
Common to All Four RS-422 Drivers
Rev: A Date: 2/08/04
SP26LV431 High Speed, +3.3V Quad RS-422 Differential Line Driver
5
© Copyright 2004 Sipex Corporationn
5 Page 
D
D1
b3
e
PACKAGE: 16 Pin PDIP
A1
A
A2
b1 L
b
INDEX
AREA
N
123
E1 E
Dimensions in (mm)
A
A1
A2
b
b2
b3
16 PIN PDIP
JEDEC MS-001
(BB) Variation
MIN NOM MAX
- - .210
.015 -
-
.115 .130 .195
.014 .018 .022
.045 .060 .070
.030 .039 .045
c .008 .010 .014
D .735 .755 .775
D1
.005 -
-
E .300 .310 .325
E1 .240 .250 .280
e .100 BSC
eA .300 BSC
eB - - .430
L .115 .130 .150
E SEE
LEAD
DETAIL
c
eA
eB
b
C
Rev: A Date: 2/08/04
16 pin PDIP
SP26LV431 High Speed, +3.3V Quad RS-422 Differential Line Driver
11
© Copyright 2004 Sipex Corporationn
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet SP26LV431.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SP26LV431 | High Speed / +3.3V Quad RS-422 Differential Line Driver | Sipex |
| SP26LV431 | HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER |  Exar |
| SP26LV432 | High Speed / Low Power Quad RS-422 Differential Line Receiver | Sipex |
| SP26LV432 | HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE RECEIVER | Exar |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |