|
|
PDF MC12149D Data sheet ( Hoja de datos )
| Número de pieza | MC12149D | |
| Descripción | LOW POWER VOLTAGE CONTROLLED OSCILLATOR BUFFER | |
| Fabricantes | Motorola Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MC12149D (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
Order this document by MC12149/D
Low Power
Voltage Controlled Oscillator
Buffer
The MC12149 is intended for applications requiring high frequency signal
generation up to 1300 MHz. An external tank circuit is used to determine the
desired frequency of operation. The VCO is realized using an
emitter–coupled pair topology. The MC12149 can be used with an integrated
PLL IC such as the MC12202 1.1 GHz Frequency Synthesizer to realize a
complete PLL sub–system. The device is specified to operate over a voltage
supply range of 2.7 to 5.5 V. It has a typical current consumption of 15 mA at
3.0 V which makes it attractive for battery operated handheld systems.
NOTE: The MC12149 is NOT suitable as a crystal oscillator.
• Operates Up to 1.3 GHz
• Space–Efficient 8–Pin SOIC or SSOP Package
• Low Power 15 mA Typical @ 3.0 V Operation
• Supply Voltage of 2.7 to 5.5 V
• Typical 900 MHz Performance
– Phase Noise –105 dBc/Hz @ 100 kHz Offset
– Tuning Voltage Sensitivity of 20 MHz/V
• Output Amplitude Adjustment Capability
• Two High Drive Outputs With a Typical Range from –8.0 to –2.0 dBm
• One Low–Drive Output for Interfacing to a Prescaler
The device has three high frequency outputs which make it attractive for
transceiver applications which require both a transmit and receive local
oscillator (LO) signal as well as a lower amplitude signal to drive the
prescaler input of the frequency synthesizer. The outputs Q and QB are
available for servicing the receiver IF and transmitter up–converter
single–ended. In receiver applications, the outputs can be used together if it
is necessary to generate a differential signal for the receiver IF. Because the
Q and QB outputs are open collector, terminations to the VCC supply are
required for proper operation. Since the outputs are complementary, BOTH
outputs must be terminated even if only one is needed. The Q and QB
outputs have a nominal drive level of –8dBm to conserve power. If addition
signal amplitude is needed, a level adjustment pin (CNTL) is available, which
when tied to ground, boosts the nominal output levels to –2.0 dBm. A low
power VCO output (Q2) is also provided to drive the prescaler input of the
PLL. The amplitude of this signal is nominally 500 mV which is suitable for
most prescalers.
External components required for the MC12149 are: (1) tank circuit (LC
network); (2) Inductor/capacitor to provide the termination for the open
collector outputs; and (3) adequate supply voltage bypassing. The tank
circuit consists of a high–Q inductor and varactor components. The
preferred tank configuration allows the user to tune the VCO across the full
supply range. VCO performance such as center frequency, tuning voltage
sensitivity, and noise characteristics are dependent on the particular
components and configuration of the VCO tank circuit.
MC12149
LOW POWER
VOLTAGE CONTROLLED
OSCILLATOR BUFFER
SEMICONDUCTOR
TECHNICAL DATA
8
1
D SUFFIX
PLASTIC PACKAGE
CASE 751
(SO–8)
8
1
SD SUFFIX
PLASTIC PACKAGE
CASE 940
(SSOP–8)
PIN CONNECTIONS
Q2 Q GND QB
8765
1234
VCC CNTL TANK VREF
(Top View)
ORDERING INFORMATION
Device
Operating
Temperature Range
Package
MC12149D
TA = – 40° to +85°C
MC12149SD
SO–8
SSOP–8
© Motorola, Inc. 1997
Rev 3
1 page  
MC12149
is a function of the capacitance value. To simplify the
selection of C1 and Cb, a table has been constructed based
on the intended operating frequency to provide
recommended starting points. These may need to be altered
depending on the value of the varactor selected.
Frequency
200 – 500 MHz
500 – 900 MHz
900 – 1200 MHz
C1
47 pF
5.1 pF
2.7 pF
Cb
47 pF
15 pF
15 pF
The value of the Cb capacitor influences the VCO supply
pushing. To minimize pushing, the Cb capacitor should be
kept small. Since C1 is in series with the varactor, there is a
strong relationship between these two components which
influences the VCO sensitivity. Increasing the value of C1
tends to increase the sensitivity of the VCO.
The parasitic contributions Lp and Cp are related to the
MC12149 as well as parasitics associated with the layout,
tank components, and board material selected. The input
capacitance of the device, bond pad, the wire bond,
package/lead capacitance, wire bond inductance, lead
inductance, printed circuit board layout, board dielectric, and
proximity to the ground plane all have an impact on these
parasitics. For example, if the ground plane is located directly
below the tank components, a parasitic capacitor will be
formed consisting of the solder pad, metal traces, board
dielectric material, and the ground plane. The test fixture
used for characterizing the device consisted of a two sided
copper clad board with ground plane on the back. Nominal
values where determined by selecting a varactor and
characterizing the device with a number of different tank/
frequency combinations and then performing a curve fit with
the data to determine values for Lp and Cp. The nominal
values for the parasitic effects are seen below:
Parasitic Capacitance
Parasitic Inductance
Cp 4.2 pF
Lp 2.2 nH
These values will vary based on the users unique circuit
board configuration.
Basic Guidelines:
1. Select a varactor with high Q and a reasonable
capacitance versus voltage slope for the desired
frequency range.
2. Select the value of Cb and C1 from the table above .
3. Calculate a value of inductance (L) which will result in
achieving the desired center frequency. Note that L
includes both LT and Lp.
4. Adjust the value of C1 to achieve the proper VCO
sensitivity.
5. Re–adjust value of L to center VCO.
6. Prototype VCO design using selected components. It
is important to use similar construction techniques and
materials, board thickness, layout, ground plane
spacing as intended for the final product.
7. Characterize tuning curve over the voltage operation
conditions.
8. Adjust, as necessary, component values – L,C1, and
Cb to compensate for parasitic board effects.
9. Evaluate over temperature and voltage limits.
10. Perform worst case analysis of tank component
variation to insure proper VCO operation over full
temperature and voltage range and make any
adjustments as needed.
Outputs Q and QB are open collector outputs and need a
inductor to VCC to provide the voltage bias to the output
transistor. In most applications, DC–blocking capacitors are
placed in series with the output to remove the DC component
before interfacing to other circuitry. These outputs are
complementary and should have identical inductor values for
each output. This will minimize switching noise on the VCC
supply caused by the outputs switching. It is important that
both outputs be terminated, even if only one of the outputs is
used in the application.
Referring to Figure 2, the recommended value for L2a and
L2b should be 47 nH and the inductor components
resonance should be at least 300 MHz greater than the
maximum operating frequency. For operation above 1100
MHz, it may be necessary to reduce that inductor value to 33
nH. The recommended value for the coupling capacitors
C6a, C6b, and C7 is 47 pF. Figure 2 also includes decoupling
capacitors for the supply line as well as decoupling for the
output inductors. Good RF decoupling practices should be
used with a series of capacitors starting with high quality 100
pF chip capacitors close to the device. A typical layout is
shown below in Figure 3.
The output amplitude of the Q and QB can be adjusted
using the CNTL pin. Refering to Figure 1, if the CNTL pin is
connected to ground, additional current will flow through the
current source. When the pin is left open, the nominal current
flowing through the outputs is 4 mA. When the pin is
grounded, the current increases to a nominal value of 10 mA.
So if a 50 ohm resistor was connected between the outputs
and VCC, the output amplitude would change from 200 mV
pp to 500 mV pp with an additional current drain for the
device of 6 mA. To select a value between 4 and 10 mA, an
external resistor can be added to ground. The equation below
is used to calculate the current.
) )(200 136 Rext) 0.8V
+ )Iout(nom)
200 (136 Rext)
Figure 4 through Figure 13 illustrate typical performance
achieved with the MC12149. The curves illustrate the tuning
curve, supply pushing characteristics, output power, current
drain, output spectrum, and phase noise performance. In
most cases, data is present for both a 750 MHz and
1200 MHz tank design. The table below illustrates the
component values used in the designs.
Component
R1
750MHz Tank
5000
1200MHz Tank
5000
Units
Ω
C1 5.1
2.7 pF
LT 4.7
1.8 nH
CV
3.7 @ 1.0 V
3.7 @ 1.0 V
pF
11 @ 4.0 V
11 @ 4.0 V
Cb 100*
15 pF
C6, C7
47
33 pF
L2 47
47 nH
NOTE: * The value of Cb should be reduced to minimize pushing.
MOTOROLA RF/IF DEVICE DATA
5
5 Page 
HP 3048A
0
MC12149
Figure 12. Typical Phase Noise Plot, 750 MHz Tank
CARRIER
784.2MHz
–25
–50
–75
–100
–125
–150
–170
100
1K
10K 100K
1M
L(f) [dBc/Hz] vs f[Hz]
10M 40M
HP 3048A
0
Figure 13. Typical Phase Noise Plot, 1200 MHz Tank
CARRIER
1220MHz
–25
–50
–75
–100
–125
–150
–170
100
1K
10K 100K
1M
L(f) [dBc/Hz] vs f[Hz]
10M 40M
MOTOROLA RF/IF DEVICE DATA
11
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet MC12149D.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MC12149D | LOW POWER VOLTAGE CONTROLLED OSCILLATOR BUFFER | Motorola Semiconductors |
| MC12149SD | LOW POWER VOLTAGE CONTROLLED OSCILLATOR BUFFER | Motorola Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |