|
|
Número de pieza | LSP2916B | |
Descripción | LSP2916 16-Channel / High-Voltage Driver | |
Fabricantes | Agere Systems | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LSP2916B (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! Preliminary Data Sheet
July 2001
LSP2916 16-Channel, High-Voltage Driver
Features
I 16 amplifier channels available in one package.
I Outputs from 0 V to –298 V per channel.
I Programmable output current limit (50 µA to
300 µA).
I Fixed gain set by internal resistors. (The fixed gain
for version A is –32 V/V, and –66 V/V for version
B.)
I Minimal external components.
Applications
I Optical crosspoint switches.
I Optical microelectromechanical systems (MEMS)
components.
Description
This LSP2916 16-channel, high-voltage (HV) driver
is targeted for microoptomechanical systems. Each
device contains 16 high-voltage amplifiers with an
output voltage range of 0 V to –298 V. Internal gain-
setting resistors provide a fixed gain of –32 V/V,
thereby minimizing external component count. Each
amplifier can output up to 300 µA, ideal for deflection
and control of optical MEMS mirrors. Output current
limit is programmed by an external resistor.
Additionally, careful attention was paid to minimizing
offset drift and gain variation over temperature. The
internal block diagram is shown in Figure 1. There
are two versions, version A (LSP2916A) and version
B (LSP2916B). For version A, RF = 8 MΩ and
RIN = 250 kΩ; and for version B, RF = 8.25 MΩ and
RIN = 125 kΩ. So LSP2916A has the fixed gain of
–32 V/V and LSP2916B has the fixed gain of
–66 V/V.
The LSP2916 requires one negative high-voltage
power supply (VHN) and one positive 5 V analog
power supply (VLP). Corresponding to the 16
channels, there are 16 negative input voltage pins,
–INx (x = 1, 2, . . . , 16), and the corresponding 16
output pins, OUTPUTx (x = 1, 2, . . . , 16).
+IN is the noninverting input for all 16 amplifiers,
which means all the amplifiers share the same
noninverting input. +IN should be connected to GND
for typical applications. IBIAS pin will set the current
limit for the amplifiers by connecting it to an external
resistor. The LSP2916 is available in a leaded
surface-mount 64-pin MQFP package.
Block Diagram
LSP2916
–IN1
RIN
RF
–
+
OUTPUT 1
–IN16
+IN
RIN
RF
–
+
OUTPUT 16
1682(F)
Figure 1. LSP2916 Internal Functional Block
Diagram
1 page Preliminary Data Sheet
July 2001
LSP2916 16-Channel, High-Voltage Driver
Electrical Characteristics
Table 4. Electrical Characteristics
TA = 25 °C, VLP = 5 V, VHN = –200 V, noninverting input +IN = 0 V, IBIAS resistor = 143 kΩ.
Parameters
Symbol
Input Characteristics
Input Resistance
Input Offset Voltage*
Input Offset Voltage
Drift
Input Noise
R
—
—
—
Input Bias Current
I(–INx)
Condition
–IN = 5 V
–IN = 0 V
–IN = 0 V
0 °C—70 °C
f ≤ 10 kHz
C = 150 pF
R = 10 MΩ
–IN = 5 V
Min
Typ
Max
Unit
2916A 2916B 2916A 2916B 2916A 2916B
125 200 500 kΩ
–20 0
20 mV
— 4 — µV/°C
— 10.3 — µVrms
12.5 25
50 µA
Input Bias Current
I(+IN)
–IN = 5 V
–40
0
Power Supply
Rejection Ratio
Input Range
PSRR
VHN
VLP
–IN
No load
No load
—
— 85
— 52
–0.5 —
Gain
Voltage Gain
Gain Temperature
Coefficient
G
GTC
–IN = 3 mV
—
30.4 63.0 32.0 66.0
— –1.25 x 10–5
Channel-to-Channel
Gain Match
—
—
—2
Amplifier Output Characteristics
Output Resistance
—
—
10 90
Amplifier Current Limit
Output Voltage
—
—
Rib = 143 kΩ
—
85
VHN + 2.5 V†
100
—
Dynamics Characteristics
–3 dB Bandwidth
—
—
— 6.5
Slew Rate
Rising
Falling
— Input pulse = 0 V—4 V
C = 150 pF and
R = 10 MΩ
—
—
0.62
0.54
Settling Time
Rising
Falling
Crosstalk§
Adjacent Channel
Nonadjacent Channel
— Input pulse = 0 V—4 V
C = 150 pF and
R = 10 MΩ
C = 150 pF
— f = 1 kHz
— R = 16 MΩ
—
—
—
—
277
309
–71
–80
* Input offset voltage = (VOFFSET voltage/gain), the test condition is for the offset output voltage.
† –IN = 10 V.
‡ –IN = –0.25 V.
§ Using an OP27 as buffer, test measurement was taken at the output of OP27.
40
—
—
10
33.6 69.0
—
—
125
115
VLPD – 3 V ‡
—
—
—
—
—
—
—
nA
dB
dB
V
V/ V
—
%
kΩ
µA
V
kHz
V/µs
V/µs
µs
µs
dB
dB
Agere Systems Inc.
5
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet LSP2916B.PDF ] |
Número de pieza | Descripción | Fabricantes |
LSP2916 | LSP2916 16-Channel / High-Voltage Driver | Agere Systems |
LSP2916A | LSP2916 16-Channel / High-Voltage Driver | Agere Systems |
LSP2916B | LSP2916 16-Channel / High-Voltage Driver | Agere Systems |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |