|
|
Número de pieza | TLE5216G | |
Descripción | Smart Quad Channel Low-Side Switch | |
Fabricantes | Siemens Semiconductor Group | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de TLE5216G (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
No Preview Available ! Smart Quad Channel Low-Side Switch
TLE 5216 G
Features
• Overload protection
• Short circuit protection
• Cascadeable serial diagnostic interface
• Overvoltage protection
• µC compatible input
• Electrostatic discharge (ESD) protection
SPT-IC
P-DSO-20-10
Type
w TLE 5216 G
w New Type
Ordering Code
Q67006-A9206
Package
P-DSO-20-10
Application
• All kinds of resistive and inductive loads (relays, electromagnetic valves)
• µC compatible power switch for 12 V applications
• Solenoid control switch in automotive and industrial control systems
Semiconductor Group
1
1998-06-22
1 page TLE 5216 G
Application Description
This IC is specially designed to drive inductive loads up to 2 A nominal current (valves,
relays, etc.). Integrated clamp-diodes limit the output voltage when inductive loads are
turned off.
For the detection of errors at the load there is a serial diagnostic interface, which
monitors the following errors for every output separately:
– open load in inactive mode
– shorted output (shorted to ground) in inactive mode
– overload or shorted load in active mode
Circuit Description
The block diagram shows the four independent power drivers with the referring logic
block and the serial diagnostic interface which stores and transfers the diagnostic
signals to the external circuit. Each power switch connects a high side load to ground
when a LOW signal applies at the inputs. To protect the IC against short circuit and over
load each output is provided with a current limitation and a delayed overload shutdown.
The slew rate of the switching process is limited internally.
The integrated clamp diodes limit the voltage at the output to V ,DS(AZ) when inductive
loads are switched off. The maximum power dissipation, which is given from the static
and dynamic thermal resistance, limits the allowable inductive energy. A diode in parallel
to every output clamps negative voltage.
All outputs, preferably the outputs 1 and 2 and the outputs 3 and 4 may be used in
parallel (no addition of max. freewheeling energy).
A curve of the output voltage is shown in figure 6.
The diagnostic block monitors the voltages across the power switch. If in active mode
(LOW level input) there is a higher voltage than VDS(OV) for a time longer than t ,VDS(OV) the
diagnostic block will show an overload in the error register and the affected power switch
will be shut off. The switch can only be reactivated if the corresponding input is switched
off and then on again.
In inactive mode (HIGH level at input) open load or shorted output (shorted load to
ground) is detected and signalled to the serial diagnostic interface. If the voltage across
the power switch is lower than VDS(OL) for the time tVDS(OL) (min. 50 µs) open load is
identified. If the voltage is even lower than VDS(SH) for the time tVDS(SH) (min. 30 µs)
"shorted to ground" is detected. An internal voltage divider will pull the output to the
voltage VDS if there is an open load.
A new error on the same output stage will over-write the old error report. The protocol of
the serial diagnostic interface includes independent error reports for each output driver.
As soon as an error is latched into the error register the serial data output (SEROUT) of
the interface will go LOW (while CS is still HIGH). If the chip select gets a LOW signal
Semiconductor Group
5
1998-06-22
5 Page TLE 5216 G
Test Circuits
100 µF
VS
+
=
VINH
=
VS
IN1 OUT1
IN2 OUT2
TLE 5216 G
IN3 OUT3
IN4 OUT4
RESET SERIN CS CLK SEROUT GND
Ι D1
Ι D2
Ι D3
Ι D4
VBB
Load
= VINL
Figure 3
Test Circuit 1
5kΩ
+
= 5V
VDS (OUT4) VDS (OUT3) VDS (OUT2) VDS (OUT1)
AES01437
100 µF
+
12 V =
IN1 VS OUT1
IN2 OUT2
TLE 5216 G
IN3 OUT3
IN4 OUT4
RESET SERIN CS CLK SEROUT GND
+
5V =
Figure 4
Test Circuit 2
Semiconductor Group
11
12 Ω
3 mH
a
b
1 nF
AES01438
1998-06-22
11 Page |
Páginas | Total 17 Páginas | |
PDF Descargar | [ Datasheet TLE5216G.PDF ] |
Número de pieza | Descripción | Fabricantes |
TLE5216 | Smart Quad Channel Low-Side Switch | Siemens Semiconductor Group |
TLE5216G | Smart Quad Channel Low-Side Switch | Siemens Semiconductor Group |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |