|
|
PDF TLE4226 Data sheet ( Hoja de datos )
| Número de pieza | TLE4226 | |
| Descripción | Intelligent Sixfold Low-Side Switch | |
| Fabricantes | Siemens Semiconductor Group | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TLE4226 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
Intelligent Sixfold Low-Side Switch
TLE 4226 G
Bipolar-IC
Features
q Quad 50 mA outputs
q Dual 500 mA outputs
q Operating range VS = 5 V ± 5 %
q Output stages with power limiting
q Open-collector outputs
q Shorted load protected within operating range
q Clamp-diodes to ground
q Status signaling
q TTL-compatible control inputs
q Overtemperature monitoring
q Temperature range – 40 to 125 ˚C
P-DSO-24-3
Type
w TLE 4226 G
w New type
Ordering Code
Q67000-A9118
Package
P-DSO-24-3 (SMD)
TLE 4226 G is an integrated, sixfold low-side power switch with power limiting of the 0.5 A outputs,
shorted-load protection of the 50 mA switches and Z-diodes on all switches from output to ground.
TLE 4226 G is particularly suitable for automotive and industrial applications.
Semiconductor Group
1
07.96
1 page  
TLE 4226 G
Circuit Description
Input Circuits
The control inputs and the preferred-state input consist of TTL-compatible Schmitt triggers with
hysteresis. Driven by these stages the buffer amplifiers convert the logic signal necessary for driving
the NPN power transistors.
Switching Stages
The output stages consist of NPN power transistors with open collectors. Each stage has its own
protective circuit for limiting power dissipation and shorted load current, which makes the outputs
shorted load protected to the supply voltage throughout the operating range. Integrated clamp-
diodes limit positive voltage spikes that occur when inductive loads are discharged. Output currents,
caused through negative voltages at the outputs, are compensated up to 50 mA for all outputs in
total.
Monitoring and Protective Functions
Each output is monitored (for overload) in its activated status. For the switches 1 to 4 overload is
detected, if the switches are activated and the output voltage at the transistor is higher than 4.1 V
for more than 10 µs. The concerned output will be shutdown and both status outputs will be set. The
switch can only be activated again if the corresponding input is switched off and then on again. If
the output voltage does not exide 4.1 V, the output is not shutdown and the status outputs are not
set, although an overload may occur. The switches 5 and 6 are protected through a SOA-circuit. It
is suppressed for at least 10 µs when the switch is turned on before it can start limiting the overload
current. The status outputs also monitor openload or shorted load to ground at the switches 5 and
6 in deactivated mode.
An analog signal is applied to the analog status output only when protection function is active. If
several malfunctions appear coincident, the highest voltage level of the analog status output will
dominate. Simultaniously the digital status output will be set.
The IC is also protected against thermal overload. If a chip temperature of typically 155 ˚C is
attained, the status outputs monitor overtemperature. If the temperature continues to increase, the
inputs and outputs of the switches 5 and 6 are shutdown. The switches 1 to 4 will not shutdown, so
precaution has to be taken in the application to prevent a further increase of the chiptemperature,
which may destroy the IC. After cooling down below 140 ˚C the overtemperature monitoring will be
reseted and the outputs of the switches 5 and 6 can be activated again.
If the minimum supply voltage for operation is not maintained, the outputs are deactivated. At a
supply voltage of higher than 1.8 V, the outputs 1 to 4 are switched on, if pin 14 (PREFST) is
connected to ground over a resistance smaller 1 MΩ. The outputs 1 to 4 can be controlled via the
inputs, if pin 14 (PREFST) is switched to high or not connected. Characteristics may be beyond the
specified values. Full function is guaranteed in the supply voltage range of 5 V ± 5 %.
Semiconductor Group
5
5 Page 
TLE 4226 G
Permissible Load Inductance versus Load
Current
Shorted Load Current IQ5, 6 versus Output
Voltage (Outputs 5 and 6)
Note:
While switching the maximum inductive loads, the maximum temperature Tj of 150 ˚C may be briefly exceeded.
The IC will not be destroyed by this, but the restrictions concerning useful life should be observed.
Semiconductor Group
11
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet TLE4226.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TLE4224-2 | Smart Low-Side Switch |  Siemens Semiconductor |
| TLE4224-S2 | Smart Low-Side Switch | Siemens Semiconductor |
| TLE4226 | Intelligent Sixfold Low-Side Switch | Siemens Semiconductor Group |
| TLE4226 | Intelligent Sixfold Low-Side Switch |  Infineon Technologies AG |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |