|
|
Número de pieza | SL1ICS3101U | |
Descripción | I.CODE1 Label IC 97pF Chip Specification | |
Fabricantes | NXP Semiconductors | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SL1ICS3101U (archivo pdf) en la parte inferior de esta página. Total 22 Páginas | ||
No Preview Available ! INTEGRATED CIRCUITS
SL1 ICS31 01
I•CODE1 Label IC (97pF)
Chip Specification
Product Specification
Revision 1.2
Public
July 2000
Philips
Semiconductors
1 page Product Specification
3 Scope
SL1 ICS31 01
Rev. 1.2
This specification describes the electrical, physical and dimensional properties of unsawn and sawn
wafers on FFC of I•CODE1 Label ICs (Cres = 97 pF) on a Philips 6C15 IDFW process and is the
base for delivery of tested I•CODE1 Label ICs.
General recommendations are given for storage, handling and processing of wafers as well as
assembly of labels.
Reference documents:
MIL-STD 883D Method 3023
MIL-STD 883D Method 3015
SNW-FQ-627
PICTOH-QS007
General Specification for 6” Wafer
General Quality Specification
I•CODE Label IC, Coil Design Guide
This product specification is valid for mask revision: VCOL1V0 NK: O MB: B
4 Ordering Information
Following ordering options are available:
Type Name
SL1 ICS31 01W/N5D
SL1 ICS31 01U/N5D
SL1 ICS31 01U/L6D
Description
Sawn wafer on foil (FFC), 150 µm, inked and mapped
Unsawn wafer, 150 µm, inked and mapped
Unsawn wafer, 525 µm, mapped (not inked)
Ordering Code
9352 670 53005
9352 670 50025
9352 670 59025
July 2000
Page 5 of 22
Public
5 Page Product Specification
8 Documentation
SL1 ICS31 01
Rev. 1.2
8.1 Delivery Documentation
Each wafer container and each larger shipment container is individually marked with the
identification information as follows:
• Diffusion Batch number (wafer lot number)
• Part designation (type) with revision number
• Ordering code (see chapter 4)
• Date code of lot acceptation
• Good die quantity
The print out of the final test results is attached to the packing and contains the good die quantity
related to every wafer number.
8.2 Fail-Die Identification
Every die is electrically tested according to data sheet. Identification of chips, which do not confirm
with the electrical parameters of the data sheet is done by inking and/or wafer mapping (all dies at
wafer periphery are identified by ‘FAIL’).
8.2.1 Ink Dot Specification
Diameter:
Height:
Colour:
Position:
Attributes:
min. 0.4 mm
max. 20 µm
black
central third of die (x, y direction)
opaque, water resistant
NOTE: Uncompleted dies with an area < 95 % (wafer periphery) are not inked!
8.2.2 Wafer Mapping
Wafer mapping for failed die identification is available on Floppy-Disk.
Format:
Electroglas ESC–ASCEND on 3.5″ Floppy-Disk
NOTE: The wafer map refers to unsawn wafers. At sawn wafers (on FFC) additional ICs
might be inked (marked as fail) if damaged during the sawing process (compared to
wafer map)!
See Appendix D for an example of the wafer map.
July 2000
Page 11 of 22
Public
11 Page |
Páginas | Total 22 Páginas | |
PDF Descargar | [ Datasheet SL1ICS3101U.PDF ] |
Número de pieza | Descripción | Fabricantes |
SL1ICS3101 | I.CODE1 Label IC 97pF Chip Specification | NXP Semiconductors |
SL1ICS3101U | I.CODE1 Label IC 97pF Chip Specification | NXP Semiconductors |
SL1ICS3101W | I.CODE1 Label IC 97pF Chip Specification | NXP Semiconductors |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |