|
|
PDF DS90C032B Data sheet ( Hoja de datos )
| Número de pieza | DS90C032B | |
| Descripción | LVDS Quad CMOS Differential Line Receiver | |
| Fabricantes | National Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de DS90C032B (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
|
No Preview Available !
September 2003
DS90C032B
LVDS Quad CMOS Differential Line Receiver
General Description
TheDS90C032B is a quad CMOS differential line receiver
designed for applications requiring ultra low power dissipa-
tion and high data rates. The device is designed to support
data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low
Voltage Differential Signaling (LVDS) technology.
TheDS90C032B accepts low voltage (350 mV) differential
input signals and translates them to CMOS (TTL compatible)
output levels. The receiver supports a TRI-STATE® function
that may be used to multiplex outputs. The receiver also
supports OPEN Failsafe and terminated (100Ω) input Fail-
safe with the addition of external failsafe biasing. Receiver
output will be HIGH for both Failsafe conditions.
The DS90C032Bprovides power-off high impedance LVDS
inputs. This feature assures minimal loading effect on the
LVDS bus lines when VCC is not present.
The DS90C032Band companion line driver (DS90C031B)
provide a new alternative to high power pseudo-ECL devices
for high speed point-to-point interface applications.
Features
n >155.5 Mbps (77.7 MHz) switching rates
n Accepts small swing (350 mV) differential signal levels
n High Impedance LVDS inputs with power down
n Ultra low power dissipation
n 600 ps maximum differential skew (5V, 25˚C)
n 6.0 ns maximum propagation delay
n Industrial operating temperature range
n Available in surface mount packaging (SOIC)
n Pin compatible with DS26C32A, MB570 (PECL) and
41LF (PECL)
n Supports OPEN and terminated input failsafe
n Conforms to ANSI/TIA/EIA-644 LVDS standard
Connection Diagram
Dual-In-Line
Functional Diagram
10099001
Order Number
DS90C032BTM
See NS Package
Number M16A
Receiver Truth Table
ENABLES
EN EN*
LH
All other
combinations
of ENABLE
inputs
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 2003 National Semiconductor Corporation DS100990
10099002
INPUTS
RIN+ − RIN−
X
VID ≥ 0.1V
VID ≤ −0.1V
Failsafe OPEN
or Terminated
OUTPUT
ROUT
Z
H
L
H
www.national.com
1 page  
Typical Application
FIGURE 5. Point-to-Point Application
10099007
Applications Information
LVDS drivers and receivers are intended to be primarily used
in an uncomplicated point-to-point configuration as is shown
in Figure 5. This configuration provides a clean signaling
environment for the quick edge rates of the drivers. The
receiver is connected to the driver through a balanced media
which may be a standard twisted pair cable, a parallel pair
cable, or simply PCB traces. Typically the characteristic
impedance of the media is in the range of 100Ω. A termina-
tion resistor of 100Ω should be selected to match the media,
and is located as close to the receiver input pins as possible.
The termination resistor converts the current sourced by the
driver into a voltage that is detected by the receiver. Other
configurations are possible such as a multi-receiver configu-
ration, but the effects of a mid-stream connector(s), cable
stub(s), and other impedance discontinuities as well as
ground shifting, noise margin limits, and total termination
loading must be taken into account.
TheDS90C032B differential line receiver is capable of de-
tecting signals as low as 100 mV, over a ±1V common-mode
range centered around +1.2V. This is related to the driver
offset voltage which is typically +1.2V. The driven signal is
centered around this voltage and may shift ±1V around this
center point. The ±1V shifting may be the result of a ground
potential difference between the driver’s ground reference
and the receiver’s ground reference, the common-mode ef-
fects of coupled noise, or a combination of the two. Both
receiver input pins should honor their specified operating
input voltage range of 0V to +2.4V (measured from each pin
to ground), exceeding these limits may turn on the ESD
protection circuitry which will clamp the bus voltages.
RECEIVER FAILSAFE
The LVDS receiver is a high gain, high speed device that
amplifies a small differential signal (20mV) to CMOS logic
levels. Due to the high gain and tight threshold of the re-
ceiver, care should be taken to prevent noise from appearing
as a valid signal.
The receiver’s internal failsafe circuitry is designed to
source/sink a small amount of current, providing failsafe
protection (a stable known state of HIGH output voltage) for
floating and terminated (100Ω) receiver inputs in low noise
environment (differential noise < 10mV).
1. Open Input Pins. TheDS90C032B is a quad receiver
device, and if an application requires only 1, 2 or 3
receivers, the unused channel(s) inputs should be left
OPEN. Do not tie unused receiver inputs to ground or
any other voltages. The input is biased by internal high
value pull up and pull down resistors to set the output to
a HIGH state. This internal circuitry will guarantee a
HIGH, stable output state for open inputs.
2. Terminated Input. TheDS90C032B requires external
failsafe biasing for terminated input failsafe.
Terminated input failsafe is the case of a receiver that
has a 100Ω termination across its inputs and the driver
is in the following situations. Unplugged from the bus, or
the driver output is in TRI-STATE or in power-off condi-
tion. The use of external biasing resistors provide a
small bias to set the differential input voltage while the
line is un-driven, and therefore the receiver output will be
in HIGH state. If the driver is removed from the bus but
the cable is still present and floating, the unplugged
cable can become a floating antenna that can pick up
noise. The LVDS receiver is designed to detect very
small amplitude and width signals and recover them to
standard logic levels. Thus, if the cable picks up more
than 10mV of differential noise, the receiver may re-
spond. To insure that any noise is seen as common-
mode and not differential, a balanced interconnect and
twisted pair cables is recommended, as they help to
ensure that noise is coupled common to both lines and
rejected by the receivers.
3. Operation in environment with greater than 10mV
differential noise.
National recommends external failsafe biasing on its
LVDS receivers for a number of system level and signal
quality reasons. First, only an application that requires
failsafe biasing needs to employ it. Second, the amount
of failsafe biasing is now an application design param-
eter and can be custom tailored for the specific applica-
tion. In applications in low noise environments, they may
choose to use a very small bias if any. For applications
with less balanced interconnects and/or in high noise
environments they may choose to boost failsafe further.
Nationals "LVDS Owner’s Manual provides detailed cal-
culations for selecting the proper failsafe biasing resis-
tors. Third, the common-mode voltage is biased by the
resistors during the un-driven state. This is selected to
be close to the nominal driver offset voltage (VOS). Thus
when switching between driven and un-driven states,
the common-mode modulation on the bus is held to a
minimum.
For additional Failsafe Biasing information, please refer
to Application Note AN-1194 for more detail.
The footprint of theDS90C032B is the same as the industry
standard 26LS32 Quad Differential (RS-422) Receiver.
For additional LVDS application information, please refer to
National’s LVDS Owner’s Manual available through Nation-
al’s website www.national.com/appinfo/lvds.
5 www.national.com
5 Page | ||
| Páginas | Total 9 Páginas | |
| PDF Descargar | [ Datasheet DS90C032B.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| DS90C032 | LVDS Quad CMOS Differential Line Receiver | National Semiconductor |
| DS90C032 | DS90C032 LVDS Quad CMOS Differential Line Receiver (Rev. D) |  Texas Instruments |
| DS90C032B | LVDS Quad CMOS Differential Line Receiver | National Semiconductor |
| DS90C032B | DS90C032B LVDS Quad CMOS Differential Line Receiver (Rev. C) | Texas Instruments |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |