|
|
PDF CXP82616 Data sheet ( Hoja de datos )
| Número de pieza | CXP82616 | |
| Descripción | CMOS 8-bit Single Chip Microcomputer | |
| Fabricantes | Sony Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CXP82616 (archivo pdf) en la parte inferior de esta página. Total 21 Páginas | ||
|
No Preview Available !
CXP82612/82616
CMOS 8-bit Single Chip Microcomputer
Description
The CXP82612/82616 microcomputer is composed
of a CPU, ROM, RAM, and I/O ports. These chips
feature many other high-performance circuits in a
single-chip CMOS design, including an A/D converter,
serial interface, timer/counter, time-base timer,
fluorescent display controller/driver, remote control
receiver and 32kHz timer/counter.
This device also includes a power-on reset function
and sleep/stop functions which can be used to
achieve low power consumption.
80 pin QFP (Plastic)
Features
• Instruction set which supports a wide array of data types
— 213 types of instructions which include 16-bit calculations, multiplication and division arithmetic, and
boolean bit operations.
• Minimum instruction cycle
400ns for 10MHz, 122µs/for 32kHz operation
• On-chip ROM
12K bytes (CXP82612)
16K bytes (CXP82616)
• On-chip RAM
448 bytes (Including fluorescent display data area)
• Peripheral functions
— A/D converter
8-bit, 8-channel, successive approximation system
(conversion rate 32µs/10MHz)
— Serial interface
On-chip 8-bit, 8-stage FIFO (1 to 8 bytes auto transfer),
1 circuit 2-channel
— Timers
8-bit timer
8-bit timer/counter
19-bit time base timer
32kHz timer/counter
— Fluorescent display controller/driver Maximum of 336 segments display available
1 to 16 digits dynamic display
Dimmer function
High voltage tolerance output (40V)
On-chip pull-down resistor (Mask option)
Hardware key scan function (Maximum of 8 × 16 key matrix available)
— Remote control receiver circuit
On-chip 6 stage FIFO 8-bit pulse measurement counter
• Interrupts
13 factors, 13 vectors multi-interruption possible
• Standby mode
Sleep/stop
• Package
80-pin plastic QFP
• Piggyback/evaluator
CXP82600 80-pin ceramic QFP
Structure
Silicon gate CMOS IC
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E93Y22A79-PS
1 page  
CXP82612/82616
Symbol
I/O
PH0 to PH1 I/O
PF0/S8
to
PF7/S15
S16 to S20
T8/S28
to
T15/S21
T0 to T7
PD0/S0
to
PD7/S7
VFDP
EXTAL
XTAL
PH2/TEX
PH3/TX
RST
NC
VDD
Vss
Output/Output
Output
Output/Output
Output
Output/Output
Input
Output
Input/Input
Input/Output
Input
Functions
(Port H)
2-bit I/O port. I/O can be set in a bit unit. Incorporation of pull-up resistor
can be set through the software in a unit of 2 bits.
(2 pins)
(Port F)
8-bit output port.
(8 pins)
Segment signal output for FDP.
Segment signal output for FDP.
Dual purpose output for FDP timing and segment signals.
Timing signal output for FDP.
(Port D)
8-bit output port.
(8 pins)
Segment signal output for FDP.
Provides voltage for FDP when on-chip resistor is selected under mask option.
Crystal connectors for system clock oscillation. When the clock is
supplied externally, input to EXTAL; opposite phase clock should be
input to XTAL.
(Port H)
2-bit input
port.
(2 pins)
Crystal connectors for 32kHz timer/counter clock
oscillation circuit. Connect a 32kHz crystal oscillator
between TEX and TX. For usage as event input, connect
clock oscillation source to TEX, and leave TX open.
Low-level active. System reset. RST is input pin.
NC.
Under normal operating conditions, connect to VDD.
Vcc supply.
GND
–5–
5 Page 
CXP82612/82616
Recommended Operating Conditions
(Vss = 0V)
Item
Symbol Min.
Max. Unit
Remarks
4.5
5.5
V
High speed mode (1/2, 1/4 clock)
guaranteed operation range
Supply voltage
VDD
3.5
5.5
V
Low speed mode (1/16 clock)
guaranteed operation range
2.7 5.5 V Guaranteed operation range with TEX clock
High level
input voltage
Low level
input voltage
2.5
5.5
V
Guaranteed data hold operation range
during stop
VIH
0.7VDD
VDD
V ∗1
VIHS
0.8VDD
VDD
V Hysteresis input∗2
VIHEX VDD – 0.4 VDD + 0.3 V EXTAL pin∗3
VIL
0
0.3VDD
V ∗1
VILS
0
0.2VDD
V Hysteresis input∗2
VILEX
–0.3
0.4 V EXTAL pin∗3
Operating temperature Topr –20 +75 °C
∗1 All regular input port (PA, PB3, PB4, PB6, PB7, PC, PE5, PH).
∗2 For pins RST, CS0, CS1, SCK0, SCK1, EC/INT0, INT1, INT2, INT3/NMI, RMC.
∗3 Specifies only for external clock input.
– 11 –
11 Page | ||
| Páginas | Total 21 Páginas | |
| PDF Descargar | [ Datasheet CXP82616.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CXP82612 | CMOS 8-bit Single Chip Microcomputer | Sony Corporation |
| CXP82616 | CMOS 8-bit Single Chip Microcomputer | Sony Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |