|
|
Número de pieza | AS8401 | |
Descripción | Multipurpose control ASIC for OMNIFET | |
Fabricantes | austriamicrosystems AG | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de AS8401 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
No Preview Available ! Austria Mikro Systeme International AG
AS8401
Multipurpose control ASIC
for OMNIFET
Data Sheet
1 page Multipurpose control ASIC for OMNINET – Data Sheet
AS8401
Austria Mikro Systeme International AG
Definition of the logic signals
Symbol Logic meaning
Level meaning
IN Control input for the driver, the input
is current controlled, i.e.:
a) According to to a current from IIN= -0,1 mA
0,1mA to DGND externally pro-
Ü
duced
b) According to no current (< 5 mA) IIN = 0
Ü
STAT
Accumulated error status signal for
the controlled OMNIFET,
the output is
current controlled, i.e.:
a) fault condition according to a
current from 0,35 mA to 0.5 mA
from the ASIC to DGND
b) normally operation according to
no current
ISTAT = -0,5mA Ü
ISTAT = 0
Ü
a) appropriate driver output goes
high (according to VOUT = VTR)
b) appropriate driver output goes
low (according to VOUT = VSOURCE)
Error at the OMNIFET during the on-
status (signal is valid after termina-
tion of the switch-on procedure)
a) an error of the OMNIFET during
the on-status,
b) normal operation or off-status of
the OMNIFET
Electrical Characteristics
Absolute Maximum Ratings (Non Operating)
SYMBOL
VTR -
VPGND
VDL
PARAMETER
DC Supply Voltage
Load Dump Voltage
MIN
-0.5 V
MAX
55 V
60V
IINmax
VINA
Tstrg
Tsold
tsold
H
ESD
Maximum Input Cur-
rent
Digital input level
Storage Temperature
Soldering Temperature
-30 mA
VPGND -
0.3V
-55 oC
Soldering Time
Humidity
5%
Electrostatic Discharge 1000 V
30 mA
55V
150 oC
260 oC
10 sec
85 %
Note:
1) 360 oC and 3s for manual soldering
NOTE
DIN 40839 vol. 2: 5 pulse, 500ms with
Ri = 2 Ohm
VIN < VInmin respectively VIN > VTR
1)
Reflow and Wave
HBM: R = 1.5 kΩ , C = 100 pF
Rev. A December 1999
Page 5 of 11
5 Page Multipurpose control ASIC for OMNINET – Data Sheet
AS8401
Package Information
Package : SOIC 8 small outline
AS8401
YY
WW
XXX
SOIC 8
Marking
Chip number
Year of Production
Week of Production
Assembly-ID
Austria Mikro Systeme International AG
SOIC 8 small outline
(Dimensions in mm)
min. nom. max.
A 1,6 1,6 1,7
A1 0,1 0,15 0,3
A2 1,40 1,5 1,6
B 0,4 0,4 0,5
C 0,19 0,2 0,3
D 4,8 4,9 5
E 3,8 3,9 3,99
e 1,27 BSC
H 5,8 5,99 6,2
h 0,25 0,33 0,41
L
0,41 0,64
0,9
α 0° 5° 8°
h x 45°
α
A
A2
A1
5
6
7
8
Figure 6: Physical package dimensions
E
H
C
L
4
3
2
1
Copyright © 1999, Austria Mikro Systeme International AG, Schloß Premstätten, 8141 Unterpremstätten, Austria.
Telefon +43-(0)3136-500-0, Telefax +43-(0)3136-52501, E-Mail [email protected]
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, without the prior permission in writing by the copyright holder. To the best of its knowledge, Austria Mikro Systeme International
asserts that the information contained in this publication is accurate and correct.
Rev. A December 1999
Page 11 of 11
11 Page |
Páginas | Total 11 Páginas | |
PDF Descargar | [ Datasheet AS8401.PDF ] |
Número de pieza | Descripción | Fabricantes |
AS8401 | Multipurpose control ASIC for OMNIFET | austriamicrosystems AG |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |