|
|
Número de pieza | ATM0430D19A-T | |
Descripción | LCD | |
Fabricantes | AZ Displays | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ATM0430D19A-T (archivo pdf) en la parte inferior de esta página. Total 19 Páginas | ||
No Preview Available ! AZ DISPLAYS
SPECIFICATIONS FOR
LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
※ PART NO. : ATM0430D19A-T (AZ DISPLAYS) VER1.0
APPROVAL
COMPANY
CHOP
CUSTOMER
COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
CHECKED BY
APPROVED BY
Herbert
1 page ATM0430D19A-T(AZ DISPLAYS) TFT MODULE V1.0
2. PIN ASSIGNMENT
TFT LCD Panel Driving Section
FPC Connector is used for the module electronics interface. The recommended model is
“FH19SC-45S-0.5SH" manufactured by Hirose.
Pin No.
1~2
3
4
5~12
13~20
21~28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Symbol
GND
VDD
/RESET
R0~R7
G0~G7
B0~B7
PCLK
DISP
HSYNC
VSYNC
DE
UD
LR
/CS
SCL
SDI
SDO
XR
YD
XL
YU
K
A
Function
Ground
Power supply
Reset pin
Red data
Green data
Blue data
Clock for Input Data
Display On/Off
Horizontal sync
Vertical sync
Data enable
Shift direction selection signal
(UD=H: Up-->Down, UD=L: Down-
->Up)
Scan direction selection signal
(LR=H: Left-->Right, LR=L: Right--
>Left)
Chip select pin of serial interface.
Leave it OPEN when not used.
Serial clock input pin. Leave it
OPEN when not used.
Serial input signal. Leave it OPEN
when not used.
Serial output signal. Leave it
OPEN when not used.
Touch panel right
Touch panel bottom
Touch panel left
Touch panel top
Power for LED backlight(Cathode)
Power for LED backlight(Anode)
Level
--
--
I
I
I
I
I
I
I
I
I
I
I
I
I
O
I
I
I
I
--
--
Note
I: input, O: output, P: Power
AZ DISPLAYS
4
5 Page ATM0430D19A-T(AZ DISPLAYS) TFT MODULE V1.0
Note 4: Definition of contrast ratio
Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.
Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel.
Note 7: Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each
measuring area.
Figure 4.3 Definition of measuring points.
Bmax: The measured maximum luminance of all measurement position.
Bmin: The measured minimum luminance of all measurement position.
AZ DISPLAYS
10
11 Page |
Páginas | Total 19 Páginas | |
PDF Descargar | [ Datasheet ATM0430D19A-T.PDF ] |
Número de pieza | Descripción | Fabricantes |
ATM0430D19A-T | LCD | AZ Displays |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |