|
|
PDF SP4082E Data sheet ( Hoja de datos )
| Número de pieza | SP4082E | |
| Descripción | 5V RS-485/RS-422 Transceivers | |
| Fabricantes | Exar | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SP4082E (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
SP4082E
5V RS-485/RS-422 Transceivers
1/8th Unit Load, Slew-Rate Limited, ±15kV ESD-Protected
FEATURES
• 5.0V single supply operation
• Receiver failsafe on open or shorted lines
• 1/8th Unit Load, 256 transceivers on bus
• Robust ESD protection for RS-485 pins
±15kV Human Body Model
• Controlled driver slew rates
115kbps, Low EMI
•Driver short circuit current limit and
thermal shutdown for overload protection
•Industry standard package footprints
RO 1
RE 2
DE 3
DI 4
8 PIN NSOIC
SP4082E
Half Duplex
8 Vcc
7B
6A
5 GND
APPLICATIONS
• Motor Control
• Building Automation
• Security Systems
• Remote Meter Reading
• Long or un-terminated transmission lines
DESCRIPTION
The SP4082E is designed for reliable, bidirectional communication on multipoint bus transmission
lines. The device contains one differential driver and one differential receiver. It is a half-duplex de-
vice. The device complys with TIA/EIA-485 and TIA/EIA-422 standards. Lead-free and RoHS compli-
ant packages are available.
This device is ruggedized for use in harsh operating conditions over the entire common-mode volt-
age range from -7V to +12V. Receivers are specially designed to fail-safe to a logic high output state
if the inputs are un-driven or shorted. All RS-485 bus-pins are protected against severe ESD events
up to ±15kV (Human Body Model). Drivers are protected from excess current flow caused by bus
contention or output short-circuits by both an internal current limit and a thermal-overload shutdown.
Devices are rated for industrial (-40 to +85ºC) operating temperatures. Receivers have exceptionally
high input impedance, which places only 1/8th the standard load on a shared bus. Up to 256 trans-
ceivers may coexist while preserving full signal margin.
The device operates from a single 5.0V power supply and draws negligible quiescent power. The
device has an independent enable and disable for the driver and receiver and will enter a low power
shutdown mode if both driver and receiver are disabled. All outputs maintain high impedance during
shutdown or when powered-off.
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510)6687000 • Fax (510)668-7017 • www.exar.com
SP4082E_100_122007
1 page  
TIMING CHARACTERISTICS
Unless otherwise noted Vcc= +5.0±0.5V, ambient temperature TA from -40 to +85ºC
DRIVER CHARACTERISTICS:
Data Signaling Rate (1 / tUI)
Driver Propagation Delay (tPHL, tPLH)
Driver Output Rise/Fall Time (tR, tF)
Driver Differential Skew (tPLH – tPHL)
Driver Enable to Output High (tDZH)
Driver Enable to Output Low (tDZL)
Driver Disable from Output High (tDHZ)
Driver Disable from Output Low (tDLZ)
Shutdown to Driver Output Valid (tDZV)
Conditions
Duty Cycle 40 to 60%
RL = 54Ω, CL = 50pF,
Min. Typ. Max. Unit
115 Kbps
3500 ns
667 1200 2500 ns
±500 ns
3500 ns
3500 ns
100 ns
100 ns
6000 ns
RECEIVER CHARACTERISTICS:
Receiver Propagation Delay
Prop. Delay Skew (tPLH – tPHL)
Receiver Output Rise / Fall Time (tR, tF)
Receiver Enable to Output High (tZH)
Receiver Enable to Output Low (tZL)
Receiver Disable from Output High (tHZ)
Receiver Disable from Output Low (tLZ)
Shutdown to Receiver Output Valid (tROV)
Time to Shutdown (Note 2,3)
Conditions
CL = 15pF, VID = ±2V
CL = 15pF
Min. Typ. Max Unit
250 ns
±50 ns
50 ns
100 ns
100 ns
100 ns
100 ns
3500 ns
50 600 ns
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510)6687000 • Fax (510)668-7017 • www.exar.com
SP4082E_100_122007
5 Page 
DETAILED DESCRIPTION
The SP4082E is a 5V half-duplex RS-485 trans-
ceiver.
The SP4082E contains one driver and one re-
ceiver. These devices feature fail-safe circuitry
that will guarantee a logic-high receiver output
when the receiver inputs are open or shorted.
The SP4082E features reduced slew-rate driv-
ers that minimize EMI and reduce reflections
caused by improperly terminated cables, allow-
ing error-free data transmission up to 115kbps.
It operates from a single 5.0V supply. Drivers
are output short-circuit current limited. Ther-
mal-shutdown circuitry protects drivers against
excessive power dissipation. When activated,
the thermal-shutdown circuitry places the driver
outputs into a high-impedance state.
Receiver FAILSAFE
Ordinary RS-485 differential receivers will be in
an indeterminate state whenever A - B is less
than ±200mV. This situation can occur when-
ever the data bus is not being actively driven.
The Failsafe feature guarantees a logic-high re-
ceiver output if the receiver’s differential inputs
are shorted or open-circuit.
The receiver thresholds of the SP4082E are
very precise and offset by at least a 40mV noise
margin from ground. This results in a logic-high
receiver output at zero volts input differential
while maintaining compliance with the EIA/TIA-
485 standard of ±200mV.
±15KV ESD PROTECTION
ESD-protection structures are incorporated on
all pins to protect against electrostatic discharg-
es encountered during handling and assembly.
The driver output and receiver inputs have ex-
tra protection against static electricity. Sipex
uses state of the art structures to protect these
pins against ESD of ±15kV without damage.
The ESD structures withstand high ESD in all
states: normal operation, shutdown, and pow-
ered down. After an ESD event, the SP4082E
keeps working without latch-up or damage.
ESD protection can be tested in various ways.
The transmitter outputs and receiver inputs of
DESCRIPTION
the SP4082E is characterized for protection to
the following limits:
±15kV using the Human Body Model
ESD TEST CONDITIONS
ESD performance depends on a variety of con-
ditions. Contact Sipex for a reliability report
that documents test setup, methodology and
results.
MACHINE MODEL
The machine model for ESD tests all pins using
a 200pF storage capacitor and zero discharge
resistance. The objective is to emulate the
stress caused when I/O pins are contacted by
handling equipment during test and assembly.
256 TRANSCEIVERS ON THE BUS
The standard RS-485 receiver input imped-
ance is 12kΩ (1 unit load). A standard driver
can drive up to 32 unit loads. The SP4032E has
only a 1/8th unit load receiver input impedance
(96kΩ), thereby allowing eight times as many,
up to 256, transceivers to be connected in par-
allel on a communication line. Any combination
of these devices and other RS-485 transceivers
up to a total of 32 unit loads may be connected
to the line.
LOW POWER SHUTDOWN MODE
Low-power shutdown mode is initiated by bring-
ing both RE high and DE low simultaneously.
While in shutdown devices typically draw only
50nA of supply current. DE and RE may be tied
together and driven by a single control signal.
Devices are guaranteed not to enter shutdown
if RE is high and DE is low for less than 50ns. If
the inputs are in this state for at least 600ns, the
parts are shutdown.
Enable times tZH and tZL apply when the part is
not in low-power shutdown state. Enable times
tZH(SHDN) and tZL(SHDN) apply when the parts
are shut down. The drivers and receivers take
longer to become enabled from low power shut-
down mode tZL(SHDN) and tZL(SHDN) than from
driver/receiver-disable mode (tZH, tZL).
DRIVER OUTPUT PROTECTION
Two mechanisms prevent excessive output cur-
rent and power dissipation caused by faults or
by bus contention. First, a driver current limit
on the output stage provides immediate protec-
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510)6687000 • Fax (510)668-7017 • www.exar.com
11
SP4082E_100_122007
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet SP4082E.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SP4082E | 5V RS-485/RS-422 Transceivers | Exar |
| SP4082E | RS-485/RS-422 Half-Duplex Transceiver |  Sipex Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |