|
|
PDF EL160.80.50 Data sheet ( Hoja de datos )
| Número de pieza | EL160.80.50 | |
| Descripción | Small Graphics Display | |
| Fabricantes | Planar Systems | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de EL160.80.50 (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
|
No Preview Available !
EL160.80.50
Small Graphics Display
USER’S MANUAL
www.planar.com
1 page  
Installation and Handling
Do not drop, bend, or flex the display. Do not allow objects to strike the
surface of the display.
CAUTION: The display uses CMOS and power MOS-FET devices. These
components are electrostatic sensitive. Unpack, assemble, and examine this
assembly in a static-controlled area only. When shipping, use packing
materials designed for protection of electrostatic-sensitive components.
Mounting
Properly mounted, EL displays can withstand high shock loads as well as
severe vibration found in demanding applications. However the glass panel
used in an EL display will break if subjected to bending stresses, high impact,
or excessive loads.
Avoid bending the display. Stresses are often introduced when a display is
mounted into a product. Ideally, the mounting tabs of the display should be
the only point of contact with the system. Use a spacer or boss for support;
failure to do so will bend the display and cause the glass to break. The
instrument enclosure or frame should not flex or distort in such a way that
during use the bending loads might be transferred to the display. Mounting
surfaces should be flat to within ±0.6 mm (±0.25"). Use all the mounting holes
provided; failure to do so will impair the shock and vibration resistance of the
final installation.
The EL160.80.50 is a tab mounted display. Use appropriate length standoffs to
assure that screws through the mounting tabs do not introduce bending
stresses into the display. Do not deflect the circuit board out of its normal
plane.
CAUTION: Properly mounted, this display can withstand high shock loads
and severe vibration in aggressive environments. However, the glass panel
used in this display will break when subjected to bending stresses, high
impact, or excessive loads.
To prevent injury in the event of glass breakage, a protective overlay should
be used on the viewer side of the display.
WARNING: These products generate voltages capable of causing personal
injury (high voltage up to 235 Vac ). Do not touch the display electronics
during operation.
EL160.80.50 Operations Manual (020-0343-00A) 3
5 Page 
Self-Test Mode
The display incorporates a self-test mode composed of two patterns displayed
for approximately 30 seconds each, and then repeated. The patterns are as
follows: Full On and 1 X 1 Checkerboard. The self-test mode is entered by
leaving pin 3 unconnected or pulled high.
Note: Pin 3 must be connected to Ground for normal display operation.
Optical
Table 5. Optical Characteristics.
Luminance
Lon (areal), min
Lon (areal), min
Loff (areal), max
40 cd/m²
79 cd/m²
0.3 cd/m²
screen center, 120 Hz frame rate
screen center, 240 Hz frame rate
3 points: center plus two ends measured
0.75 0.25" from adjacent display edges, @
240 Hz
Non-uniformity
All pixels fully lit
35% Maximum difference two of five points,
using the formula:
LNU%=[1- (min_lum/max_lum)] x 100%
Luminance Variation (Temperature)
Maximum
20% Across operating temperature range
Luminance Variation (Time)
Maximum
<20%
10,000 hours at 25 C ambient
Viewing Angle
Minimum
160
Contrast Ratio
Typical
50:1 @ 500 lux ambient, 240 Hz frame rate
Dimming
There are two standard methods for dimming the EL160.80.50 display. Frame
rate dimming allows the brightness of the display to be lowered proportionally
by reducing the frame rate. Frame rate dimming is performed within the
application by lowering the frame rate of the video input signals. Because
brightness is proportional to frame rate, the display can be dimmed by adding
pauses between every horizontal period.
The lowest useable frame rate (brightness) is dependent on the perceived
flicker of the displayed image, but will most likely be around 60 Hz.
Dimming control circuitry is available on some models of this display. This
feature allows manual analog dimming of the brightness from 100% to
approximately 5% of the full brightness.
For models which feature analog dimming, connect a 100 k ohm logarithmic
external potentiometer to the dimming port. Alternatively, an external voltage
or current mode D/A converter may be used to facilitate dimming by sinking a
maximum of 250 µA (for maximum dimming) from pin 1 to pin 2 of the
dimming connector.
EL160.80.50 Operations Manual (020-0343-00A) 9
11 Page | ||
| Páginas | Total 17 Páginas | |
| PDF Descargar | [ Datasheet EL160.80.50.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| EL160.80.50 | Small Graphics Display | Planar Systems |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |