|
|
PDF CleO50 Data sheet ( Hoja de datos )
| Número de pieza | CleO50 | |
| Descripción | smart TFT display shield for Arduino and MikroBUS | |
| Fabricantes | Bridgetek | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CleO50 (archivo pdf) en la parte inferior de esta página. Total 29 Páginas | ||
|
No Preview Available !
Future Technology
Devices International
Limited
Datasheet
CleO50 Module
CleO50 Module Datasheet
Version 1.0
Document Reference No.: FT_001342 Clearance No.: BRT#045
1 Introduction
The CleO50 is a smart TFT display shield for
Arduino and MikroBUS. It includes a 5.0 inch
800x480 pixel TFT LCD panel with resistive touch,
PWM audio output with in-built speaker amplifier for
better audio quality.
These smart TFT display shields can be easily
programmed by almost anyone to give
professional looking HMI / GUI's with no prior
knowledge of complex graphics programming or
mathematics.
Support landscape and portrait modes
In built FTDI FT812 embedded video engine
(EVE) graphic controller
Anti-aliased graphics throughout for much finer
image quality with no "jaggies"
Ready to use LCD module with resistive touch
in panel mountable bezel
USB DFU port for firmware updates
In built 8M Byte Eflash memory
1.1 Features
The CleO50 utilises the FTDI FT900 low power MCU
to bridge between the Arduino and fast interface
accessories such as MikroBUS, camera and SD Card
input. For a full list of the FT900’s features refer to
the FT90X datasheet. In addition, the CleO50 has
the following features:
PWM audio supported and in built speaker
amplifier
Support MikroBUS interface
Support Micro SD card
Support camera interface
Support I2S interface
Support CAN bus
Support RTC function
Designed as Arduino and NerO shield
Compatible with FTDI CleO-RIO, CleO-Camera
and CleO-Speaker
CE and FCC certified
Note: MikroBus interface is created by MikroElektronika is an
open standard anyone can implement in their design. Please
visit MikroE for more detail
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or
reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its
documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or
implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of u se or
failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any
medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury.
This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other
intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2
Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640
Copyright © Bridgetek Limited
1
1 page  
4 Module Hardware Feature
CleO50 Module Datasheet
Version 1.0
Document Reference No.: FT_001342 Clearance No.: BRT#045
The dimensions of the CleO50 module are 142 mm x 99 mm X17.8mm. See Figure 1 for all the hardware
features.
Figure 1 - CleO50 Bottom View
Key Features:
1 Speaker out / Line in
3 5.0 in HVGA TFT I/F + Resistive Touch
5 Arduino I/F
7 Battery Holder
9 FT900 MCU
11 Camera Interface
2 Plastic Bezel
4 Arduino Configuration Jumpers
6 Level Shifter
8 USB DFU Connector
10 MicroSD Card Socket
12 MikroBus Interface
13 I2S & Can Bus Interface
14 FT812 GPU
15 8M Byte E-Flash
16 Audio Amplifier
17 Power indicator LED
18 RTC Circuitry
Copyright © Bridgetek Limited
5
5 Page 
CleO50 Module Datasheet
Version 1.0
Document Reference No.: FT_001342 Clearance No.: BRT#045
4.6 Audio Output
Figure 5 – Camera Interface
CleO50 supports a mono speaker output through CN2. Maximum output power, can drive up to 8 OHM, 1
Watt speaker driver. A readymade speaker module(CleO-SPK1) is also available from FTDI, visit the FTDI
Chip website for more information.
An alternative, mono line-in audio input is also provided on CN2. Users can drive in their own audio
source to the on board power amplifier. See the Table 3 for the pin list for CN2.
Pin No.
1
2
3
4
Pin Name
Description
SP- Speaker Out Negative
SP+
Speaker Out Positive
GND
Ground
EXT_AUD
Ext Audio Line In
Table 3 – Audio Connector Pin Out
Copyright © Bridgetek Limited
11
11 Page | ||
| Páginas | Total 29 Páginas | |
| PDF Descargar | [ Datasheet CleO50.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CleO50 | smart TFT display shield for Arduino and MikroBUS | Bridgetek |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |