|
|
PDF MB95F816K Data sheet ( Hoja de datos )
| Número de pieza | MB95F816K | |
| Descripción | New 8FX 8-bit Microcontrollers | |
| Fabricantes | Cypress Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MB95F816K (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
MB95810K Series
New 8FX 8-bit Microcontrollers
The MB95810K Series is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the
microcontrollers of these series contain a variety of peripheral resources.
Features
■ F2MC-8FX CPU core
❐ Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instructions
• Bit manipulation instructions, etc.
■ Clock
❐ Selectable main clock source
• Main oscillation clock (up to 16.25 MHz, maximum ma-
chine clock frequency: 8.125 MHz)
• External clock (up to 32.5 MHz, maximum machine clock
frequency: 16.25 MHz)
• Main CR clock (4 MHz 2%)
• Main CR PLL clock
- The main CR PLL clock frequency becomes 8 MHz
2% when the PLL multiplication rate is 2.
- The main CR PLL clock frequency becomes 10 MHz
2% when the PLL multiplication rate is 2.5.
- The main CR PLL clock frequency becomes 12 MHz
2% when the PLL multiplication rate is 3.
- The main CR PLL clock frequency becomes 16 MHz
2% when the PLL multiplication rate is 4.
❐ Selectable subclock source
• Suboscillation clock (32.768 kHz)
• External clock (32.768 kHz)
• Sub-CR clock (Typ: 100 kHz, Min: 50 kHz, Max: 150 kHz)
■ Timer
❐ 8/16-bit composite timer 2 channels
❐ 8/16-bit PPG 2 channels
❐ 16-bit PPG timer 2 channels
❐ 16-bit reload timer 1 channel
❐ Time-base timer 1 channel
❐ Watch prescaler 1 channel
■ UART/SIO 1 channel
❐ Full duplex double buffer
❐ Capable of clock asynchronous (UART) serial data transfer
and clock synchronous (SIO) serial data transfer
■ I2C bus interface 1 channel
❐ Built-in wake-up function
■ LIN-UART
❐ Full duplex double buffer
❐ Capable of clock asynchronous serial data transfer and clock
synchronous serial data transfer
■ External interrupt 12 channels
❐ Interrupt by edge detection (rising edge, falling edge, and
both edges can be selected)
❐ Can be used to wake up the device from different low power
consumption (standby) modes
■ 8/10-bit A/D converter 12 channels
❐ 8-bit or 10-bit resolution can be selected.
■ Low power consumption (standby) modes
❐ There are four standby modes as follows:
• Stop mode
• Sleep mode
• Watch mode
• Time-base timer mode
❐ In standby mode, two further options can be selected: normal
standby mode and deep standby mode.
■ I/O port (no. of I/O ports: 58)
❐ General-purpose I/O ports (CMOS I/O): 54
❐ General-purpose I/O ports (N-ch open drain): 4
■ On-chip debug
❐ 1-wire serial control
❐ Serial writing supported (asynchronous mode)
■ Hardware/software watchdog timer
❐ Built-in hardware watchdog timer
❐ Built-in software watchdog timer
■ Power-on reset
❐ A power-on reset is generated when the power is switched
on.
■ Low-voltage detection (LVD) reset circuit
❐ The LVD function is enabled by default. For details, see “18.2
Recommended Operating Conditions” in
“Electrical Characteristics”.
❐ The LVD function can be controlled through software.
❐ The LVD reset circuit control register (LVDCC) enables or
disables the LVD reset.
❐ The LVD reset circuit has an internal low-voltage detector.
The combination of detection voltage and release voltage
can be selected from four options.
■ Comparator 2 channels
❐ Built-in dedicated BGR
❐ The comparator reference voltage can be selected between
the BGR voltage and the comparator pin.
■ Clock supervisor counter
❐ Built-in clock supervisor counter
■ Dual operation Flash memory
❐ The program/erase operation and the read operation can be
executed in different banks (upper bank/lower bank) simul-
taneously.
■ Flash memory security function
❐ Protects the content of the Flash memory.
Cypress Semiconductor Corporation • 198 Champion Court
Document Number: 002-04694 Rev. *A
• San Jose, CA 95134-1709 • 408-943-2600
Revised March 29, 2016
1 page  
MB95810K Series
Part number
MB95F814K
MB95F816K
MB95F818K
Parameter
Standby mode
There are four standby modes as follows:
• Stop mode
• Sleep mode
• Watch mode
• Time-base timer mode
In standby mode, two further options can be selected: normal standby mode and deep standby mode
Package
FPT-64P-M38
FPT-64P-M39
2. Packages And Corresponding Products
Part number
Package
FPT-64P-M38
FPT-64P-M39
MB95F814K
MB95F816K
MB95F818K
: Available
3. Differences Among Products And Notes On Product Selection
• Current consumption
When using the on-chip debug function, take account of the current consumption of Flash program/erase.
For details of current consumption, see “Electrical Characteristics”.
• Package
For details of information on each package, see “Packages And Corresponding Products” and “Package Dimension”.
• Operating voltage
The operating voltage varies, depending on whether the on-chip debug function is used or not.
For details of operating voltage, see “Electrical Characteristics”.
• On-chip debug function
The on-chip debug function requires that VCC, VSS and one serial wire be connected to an evaluation tool. For details
of the connection method, refer to “CHAPTER 25 EXAMPLE OF SERIAL PROGRAMMING CONNECTION” in “New
8FX MB95810K Series Hardware Manual”.
Document Number: 002-04694 Rev. *A
Page 5 of 121
5 Page 
6. I/O Circuit Type
Type
A
B
X1
Circuit
Reset input / Hysteresis input
Reset output / Digital output
N-ch
P-ch
N-ch
Port select
Digital output
Digital output
Standby control
Hysteresis input
Clock input
X0
Standby control / Port select
P-ch
N-ch
C
R
P-ch
P-ch
N-ch
X1A
Port select
Digital output
Digital output
Standby control
Hysteresis input
Port select
Pull-up control
Digital output
Digital output
Standby control
Hysteresis input
Clock input
X0A
Standby control / Port select
R
Digital output
P-ch
N-ch
Port select
Pull-up control
Digital output
Digital output
Standby control
Hysteresis input
Document Number: 002-04694 Rev. *A
MB95810K Series
Remarks
• N-ch open drain output
• Hysteresis input
• Reset output
• Oscillation circuit
• High-speed side
Feedback resistance:
approx. 1 M
• CMOS output
• Hysteresis input
• Oscillation circuit
• Low-speed side
Feedback resistance:
approx. 5 M
• CMOS output
• Hysteresis input
• Pull-up control
Page 11 of 121
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet MB95F816K.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MB95F816K | New 8FX 8-bit Microcontrollers | Cypress Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |