|
|
Número de pieza | CYBLE-222014-01 | |
Descripción | EZ-BLE PRoC Module | |
Fabricantes | Cypress Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CYBLE-222014-01 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! PRELIMINARY
CYBLE-222014-01
EZ-BLE™ PRoC™ Bluetooth 4.2 Module
General Description
The Cypress CYBLE-222014-01 is a fully certified and qualified
module supporting Bluetooth Low Energy (BLE) 4.2 wireless
communication. The CYBLE-222014-01 is a turnkey solution
and includes onboard crystal oscillators, chip antenna, passive
components, and Cypress PRoC™ BLE. Refer to the
CYBL10X7X datasheet for additional details on the capabilities
of the PRoC BLE device used on this module.
The CYBLE-222014-01 supports a number of peripheral
functions (ADC, timers, counters, PWM) and serial
communication protocols (I2C, UART, SPI) through its
programmable architecture. The CYBLE-222014-01 includes a
royalty-free BLE stack compatible with Bluetooth 4.2 and
provides up to 16 GPIOs in a small 10 × 10 × 1.80 mm package.
The CYBLE-222014-01 is drop-in compatible with the
CYBLE-022001-00 (128KB BT 4.1) and CYBLE-222005-00
(256KB BT 4.1).
Module Description
■ Module size: 10.0 mm ×10.0 mm × 1.80 mm (with shield)
■ 256-KB flash memory, 32-KB SRAM memory
■ Up to 16 GPIOs configurable as open drain high/low,
pull-up/pull-down, HI-Z analog, HI-Z digital, or strong output
■ Bluetooth 4.2 qualified single-mode module
■ Certified to FCC, CE MIC, KC, and IC regulations
■ Eight-channel direct memory access (DMA) controller
■ 32-bit processor (0.9 DMIPS/MHz) with single-cycle 32-bit
multiply, operating at up to 48 MHz
■ Industrial temperature range: –40 °C to +85 °C
■ Watchdog timer with dedicated internal low-speed oscillator
(ILO)
■ Two-pin SWD for programming
Power Consumption
■ TX output power: –18 dbm to +3 dbm
■ Received signal strength indicator (RSSI) with 1-dB resolution
■ TX current consumption of 15.6 mA (radio only, 0 dbm)
■ RX current consumption of 16.4 mA (radio only)
■ Low power mode support
❐ Deep Sleep: 1.3 µA with watch crystal oscillator (WCO) on
❐ Hibernate: 150 nA with SRAM retention
❐ Stop: 60 nA with XRES wakeup
Functional Capabilities
■ Up to 15 capacitive sensors for buttons or sliders with
best-in-class signal-to-noise ration (SNR) and liquid tolerance
■ 12-bit, 1-Msps SAR ADC with internal reference,
sample-and-hold (S/H), and channel sequencer
■ Two serial communication blocks (SCBs) supporting I2C
(master/slave), SPI (master/slave), or UART
■ Four dedicated 16-bit timer, counter, or PWM blocks
(TCPWMs)
■ Programmable low-voltage detect (LVD) from 1.8 V to 4.5 V
■ I2S master interface
■ Bluetooth Low Energy protocol stack supporting generic
access profile (GAP) Central, Peripheral, Observer, or
Broadcaster roles
■ Switches between Central and Peripheral roles on-the-go
■ Standard Bluetooth Low Energy profiles and services for
interoperability
■ Custom profile and service for specific use cases
Benefits
The CYBLE-222014-01 module is provided as a turnkey
solution, including all necessary hardware required to use BLE
communication standards.
■ Proven, qualified, and certified hardware design ready to use
■ Small footprint (10 × 10 mm × 1.80 mm), perfect for space
constrained applications
■ Reprogrammable architecture
■ Fully-certified module eliminates the time needed for design,
development and certification processes
■ Bluetooth SIG qualified with QDID and Declaration ID
■ Flexible communication protocol support
■ PSoC® Creator™ provides an easy-to-use integrated design
environment (IDE) to configure, develop, program, and test a
BLE application
Cypress Semiconductor Corporation
Document Number: 002-11186 Rev. *A
198 Champion Court
San Jose, CA 95134-1709 408-943-2600
Revised March 23, 2016
1 page PRELIMINARY
Figure 1. Module Mechanical Drawing
CYBLE-222014-01
Top View
Side View
Bottom View
Note
1. No metal should be located beneath or above the antenna area. Only bare PCB material should be located beneath the antenna area. For more information on
recommended host PCB layout, see “Recommended Host PCB Layout” on page 7.
Document Number: 002-11186 Rev. *A
Page 5 of 37
5 Page PRELIMINARY
The CYBLE-222014-01 schematic is shown in Figure 9.
Figure 9. CYBLE-222014-01 Schematic Diagram
CYBLE-222014-01
Document Number: 002-11186 Rev. *A
Page 11 of 37
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet CYBLE-222014-01.PDF ] |
Número de pieza | Descripción | Fabricantes |
CYBLE-222014-01 | EZ-BLE PRoC Module | Cypress Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |