|
|
PDF PI3VDP612-A Data sheet ( Hoja de datos )
| Número de pieza | PI3VDP612-A | |
| Descripción | 4-Lane DisplayPort Rev 1.1a Compliant Switch | |
| Fabricantes | Pericom Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PI3VDP612-A (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
PI3VDP612-A
4-Lane DisplayPort™ Rev 1.1a Compliant Switch
with Triple Control Logic for Fast Switching
Features
ÎÎ4-lane, 1:2 mux/demux that will support 2.7Gbps or
1.62Gbps DP rev 1.1a signals
ÎÎ1-channel 1:2 mux/demux for DP_HPD signal
ÎÎ1-differential channel 1:2 mux/demux for DP_Aux signal
ÎÎInsertion Loss for high speed channels @ 2.7 Gbps: -1.5dB
ÎÎ-3dB Bandwidth for high speed channels of 3.25 Ghz
ÎÎLow Bit-to-Bit Skew , 7ps max (between '+' and '-' bits)
ÎÎVDD Operating Range: 3.3V ±10%
ÎÎESD Tolerance: +/-8kV contact on Ports A and B per
IEC61000-4-2 Specification
ÎÎLow channel-to-channel skew, 35ps max
ÎÎPackaging (Pb-free & Green):
àà -56 TQFN (ZFE)
àà -42 TQFN (ZHE)
Description
Pericom Semiconductor’s PI3VDP612-A mux/demux is targeted
for next generation digital video signals. This device can be used
to connect a DisplayPort™ Source to two Independent Display-
Port Sinks or to connect two DisplayPort sources to a single DP
display.
The newly released DisplayPort spec requires a data rate of 2.7
Gbps with AC coupled I/Os. Pericom's solution has been specifi-
cally designed around this standard and will support such sig-
nals.
Application
Routing of DisplayPort signals with low signal attenuation be-
tween source and sink.
Block Diagram
Pin Description - 56-Pin
D0+
D0-
D1+
D1-
D2+
D2-
D3+
D3-
AUX+
AUX-
HPD
CAB_DET/LED
D0+A
D0-A
D1+A
D1-A
D2+A
D2-A
D3+A
D3-A
D0+B
D0-B
D1+B
D1-B
D2+B
D2-B
D3+B
D3-B
AUX+ A
AUX- A
HPD A
CAB_DETA/LEDA
AUX+ B
AUX- B
HPD B
CAB_DETB/LEDB
AUX_SEL
D0+
D0-
D1+
D1-
VDD
D2+
D2-
D3+
D3-
GND
AUX+
AUX-
HPD
CAB_DET/LED
GND
VDD
SEL1
SEL2
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
GND
48 GND
47 D2+A
46 D2-A
45 D3+A
44 D3-A
43 D0+B
42 D0-B
41 D1+B
40 D1-B
39 D2+B
38 D2-B
37 D3+B
36 D3-B
35 GND
34 VDD
33 AUX+A
32 AUX-A
31 HPD_A
30 CAB_DET/LEDA
29 GND
SEL2
SEL1
AUX_SEL
11-0103
Logic
Control
1
PS9056A
07/12/11
1 page  
PI3VDP612-A
4-Lane DisplayPort™ Rev 1.1a Compliant Switch
with Triple Control Logic for Fast Switching
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .....................................................–65°C to +150°C
Supply Voltage to Ground Potential ................................–0.5V to +3.6V
Note: Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This
is a stress rating only and functional operation of the device
DC Input Voltage ............................................................... –0.7V to 3.6V
DC Output Current ....................................................................... 120mA
Power Dissipation ............................................................................ 0.5W
at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Expo-
sure to absolute maximum rating conditions for extended
periods may affect reliability.
DC Electrical Characteristics for Switching over Operating Range (TA = –40°C to +85°C, VDD =
3.3V ±10%)
Parameter
VIH
VIL
VIK
IIH
IIL
IOFF
RON
Description
Input HIGH Voltage
Input LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
I/O leakage when part is off
On resistance between input to
output
Test Conditions(1)
Guaranteed HIGH level
Guaranteed LOW level
VDD = Max., IIN = –18mA
VDD = Max., VIN = VDD
VDD = Max., VIN = GND
VDD = 0V, VINPUT = 0V to 3.6V
VDD = 3.0V, -0.6V<VINPUT<0.6V
VDD = 3.0V, 1.0V<VINPUT<1.5V
Min Typ(1) Max Units
1.6
–0.7
0.75 V
–1.2
±5
±5 µA
50
7 Ohm
10 Ohm
Power Supply Characteristics (TA = 0°C to +70°C)
Parameter Description
Test Conditions(1)
ICC
Quiescent Power Supply Current
VDD = Max., VIN = GND or VDD
Min
Typ(1) Max
70
Units
µA
Dynamic Electrical Characteristics over Operating Range (TA = -40º to +85ºC, VDD = 3.3V ±10%,
GND=0V)
Parameter
Description
Test Conditions
Typ.(2) Units
XTALK
OIRR
Crosstalk on High Speed Channels
See Fig. 1 for Measurement
Setup
OFF Isolation on High Speed Channels
See Fig. 2 for Measurement
Setup,
f= 1.35 GHz
f = 100 MHz
f= 1.35 GHz
f = 100 MHz
-33dB
-48dB
-33dB
-56dB
dB
ILOSS
BW_Dx±
BW_AUX/HPD
Differential Insertion Loss on High
Speed Channels
Bandwidth -3dB for Main high speed
path (Dx±)
-3dB BW for AUX and HPD signals
@2.7Gbps (see figure 3)
See figure 3
See figure 3
-1.5 dB
3.25 GHz
1.5 GHz
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VDD = 3.3V, Ta = 25°C ambient and maximum loading.
11-0103
5
PS9056A
07/12/11
5 Page 
PI3VDP612-A
4-Lane DisplayPort™ Rev 1.1a Compliant Switch
with Triple Control Logic for Fast Switching
Switching Characteristics (TA= -40º to +85ºC, VDD = 3.3V±10%)
Parameter
Description
tPZH, tPZL
tPHZ, tPLZ
Tpd
tb-b
tch-ch
Line Enable Time
Line Disable Time
Propagation delay (input pin to output pin)
Bit-to-bit skew within the same differential pair
Channel-to-channel skew
Test Circuit for Electrical Characteristics(1-5)
VDD
Min.
0.5
0.5
Max.
15.0
15.0
200
7
50
Units
ns
ps
ps
ps
6.0V
Pulse
Generator
VIN
RT
D.U.T
VOUT
200-ohm
4pF
CL
200-ohm
Notes:
1. CL = Load capacitance: includes jig and probe capacitance.
2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator
3. Output 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
output 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
4. All input impulses are supplied by generators having the following characteristics: PRR ≤ MHz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns.
5. The outputs are measured one at a time with one transition per measurement.
Switching Waveforms
SEL
tPZL
Output 1
tPZH
Output 2
VDD/2
tPLZ
VDD/2
tPHZ
VDD/2
VDD/2
VOL + 0.3V
VOH – 0.3V
VDD
0V
VOH
VOL
VOH
VOL
Voltage Waveforms Enable and Disable Times
Switch Positions
Test
tPLZ, tPZL (output on B-side)
tPHZ, tPZH (output on B-side)
Prop Delay
Switch
6.0V
GND
Open
11-0103
11
PS9056A
07/12/11
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet PI3VDP612-A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PI3VDP612-A | 4-Lane DisplayPort Rev 1.1a Compliant Switch | Pericom Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |