DataSheet.es    

Datasheet MS21042 Equivalent ( PDF )

N.º Número de pieza Descripción Fabricantes Category
1MS21042(MS210xx) Nut

MS21083 LOW PROFILE - NYLON INSERT SUPERSEDES AN364 - MS20364 MAXIMUM TEMP. 250 DEG. F. TO FIT THREAD SIZE CARBON STEEL AN364 440A 632A 832A 1032A 428A 524A 624A * 820A 918A 1018A MS 21083 N04 N06 N08 N3 N4 N5 N6 N7 N8 N9 N10 CORROSION RESISTANT AN364C C440A C632A C832A C1032A
Aviaquip
Aviaquip
data
2MS21042MS21042

— .—-— \ r \ .&-& DREION OF WRENCEINO PAO FACES wTw=NwRmmnom cORNEmSm CURNEna MIEwtTtIoi TnGLIUITaoT OPTIONAL IF THE wRExwlNo Z. W, ANO C BEFORE LUBRICATICWAND TRE LM1’1’ OF TRB AREA BETWRBN TRE CORNE3W3SWITRIN. TREMAX3MU?4 LIMCC OF W FQR THE E LENOTE or W4ENCR3NOCO
Military Specification
Military Specification
data
3MS21042Nuts

MS21042 / NAS1291 Series Specifications Nuts, Self-locking, 450°, Reduced Hexagon, Reduced Height, Ring Base, Non-Corrosion Resistant Steel 35 Size Dash No. 02 04 06 08 3 4 5 6 7 8 9 10 Thread a 2-56 UNC-3B 4-40 UNC-3B 6-32 UNC-3B 8-32 UNC-3B 10-32 UNF-3B 1/4-28 UNF-3B 5/16-24 UNF-3B 3/8-24 UNF
Coast Fabrication
Coast Fabrication
data
4MS21042L3MS21042

— .—-— \ r \ .&-& DREION OF WRENCEINO PAO FACES wTw=NwRmmnom cORNEmSm CURNEna MIEwtTtIoi TnGLIUITaoT OPTIONAL IF THE wRExwlNo Z. W, ANO C BEFORE LUBRICATICWAND TRE LM1’1’ OF TRB AREA BETWRBN TRE CORNE3W3SWITRIN. TREMAX3MU?4 LIMCC OF W FQR THE E LENOTE or W4ENCR3NOCO
Military Specification
Military Specification
data


MS2 Datasheet ( Hoja de datos ) - resultados coincidentes

N.º Número de pieza Descripción Fabricantes PDF
1MS20001Hinge / Butt / Structural / Extruded

Genuine Aircraft Hardware Co. Hinge, Butt, Structural, Extruded MS20001 TABLE I * CANCELLED - NO SUPERSEDING PART NUMBER ( a ) TOLERANCES FOR DIMENSIONS ON PITCH SHALL NOT BE CUMULATIVE. ( b ) DIMENSIONS K MUST NEVER EXCEED A FULL LOOP OR TANG, AND BOTH ENDS MUST BE EQUAL WITHIN .020 INCH. INTERC
Genuine Aircraft
Genuine Aircraft
datasheet MS20001 pdf
2MS20001STRUCTURAL EXTRUDED HINGE

STRUCTURAL EXTRUDED HINGE STANDARD LENGTH 72 INCHES OTHER LENGTHS AVAILABLE ON REQUEST. MS20001 Dash Number -2 -3 -4 -5 -6 -8 A Ref Width Open 1.062 1.250 1.500 1.750 2.000 2.000 B (Thickness) Max. Min. D Loop Hole Dia. +.005 P Pitch Pin Diameter .056 .044 .495 .093 1.00” .090 .076
AVIAQUIP
AVIAQUIP
datasheet MS20001 pdf
3MS20001PHinge / Butt / Structural / Extruded

INCH-POUND MS20001P 21 May 2012 SUPERSEDING MS20001N 16 November 2010 DETAIL SPECIFICATION SHEET HINGE, BUTT STRUCTURAL, EXTRUDED This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. FIGURE 1. Butt hinge. AMSC N/A FSC 5340 MS20001P TABLE I.
ETC
ETC
datasheet MS20001P pdf
4MS20004Diameter / Head Size / Lengths

www.datasheet4u.com www.datasheet4u.com
Genuine Aircraft
Genuine Aircraft
datasheet MS20004 pdf
5MS20004MS20004 - MS20014

www.datasheet4u.com 16761 Burke Lane, Huntington Beach, CA 92647 Phone: 714-842-2603 Fax: 714-847-182467 info [email protected]
ETC
ETC
datasheet MS20004 pdf
6MS20005Diameter / Head Size / Lengths

www.datasheet4u.com www.datasheet4u.com
Genuine Aircraft
Genuine Aircraft
datasheet MS20005 pdf
7MS20005MS20004 - MS20014

www.datasheet4u.com 16761 Burke Lane, Huntington Beach, CA 92647 Phone: 714-842-2603 Fax: 714-847-182467 info [email protected]
ETC
ETC
datasheet MS20005 pdf



Esta página es del resultado de búsqueda del MS21042. Si pulsa el resultado de búsqueda de MS21042 se puede ver detalladamente sobre la hoja de datos, el circuito y la disposición de pin.

nuevas actualizaciones

Número de pieza Descripción Fabricantes PDF
SPS122

Modern EU gaming Machines require increased +12V current to accommodate the latest gaming peripherals. DC Converters have been engineered with Sanken’s latest technology to efficiently convert redundant power from our lamp gaming PSU and provide additional +12V capacity at the point of use.

Sanken
Sanken
PDF


DataSheet.es    |   2020    |  Privacy Policy  |  Contacto  |  Sitemap