|
|
PDF 5037 Data sheet ( Hoja de datos )
| Número de pieza | 5037 | |
| Descripción | 2.5V LVDS Output Oscillator ICs | |
| Fabricantes | NPC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 5037 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
5037 series
2.5V LVDS Output Oscillator ICs
OVERVIEW
The 5037 series are 2.5V operation, LVDS output oscillator ICs. They support 80MHz to 400MHz 3rd over-
tone oscillation and 80MHz to 600MHz fundamental oscillation. The 5037 series can be used to construct
high-frequency LVDS output oscillators.
FEATURES
I 2.375 to 3.6V operating supply voltage range
I Recommended oscillation frequency range (varies
with version)
• 80MHz to 600MHz fundamental oscillation
• 80MHz to 400MHz 3rd overtone oscillation
I – 40 to 85°C operating temperature range
I LVDS output
I Standby function
• Outputs are high impedance when OE is LOW.
(oscillator stops)
I Power-saving pull-up resistor built-in (pin OE)
I BiCMOS process
I Chip form (CF5037××, CF5037×××)
SERIES CONFIGURATION
Version
5037A1
5037B×
5037C×
5037D×
5037E×
5037D1T
Built-in C0
Recommended C0
cancellation circuit
value [pF]
≥2
Yes
2
≥ 2.5
Recommended
crystal unit/
resonator
Fundamental,
3rd overtone,
SAW
Fundamental,
SAW
Fundamental,
3rd overtone,
SAW
Recommended
oscillation frequency
range*1 [MHz]
80 to 120
100 to 180
150 to 250
250 to 400
400 to 600
250 to 400
Output frequency*2
fO
5037A1
5037B1
5037C1
5037D1
5037E1
fO/2
–
5037B2*3
5037C2
5037D2
(5037E2)
5037D1T
–
5037A1N
5037B1N
No
≤ 2.5
Fundamental,
SAW
80 to 120
110 to 180
5037A1N
5037B1N
–
–
*1. The recommended oscillation frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscilla-
tor frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the
oscillation characteristics of components must be carefully evaluated.
*2. This version in parentheses ( ) is under development. Please ask our Sales & Marketing section for further detail.
*3. Minimum output frequency: 80MHz
ORDERING INFORMATION
Device
Package
CF5037××–1
CF5037D1T–1
Chip form
CF5037×1N–3
Version name
CF5037
Form CF: Chip (Die) form
−
Chip thickness 1: 300 ± 30µm
3: 180 ± 20µm
N: Not built-in C0 cancellation circuit
T: 3rd overtone
Frequency divider function
Oscillation frequency range
SEIKO NPC CORPORATION —1
1 page  
5037 series
SPECIFICATIONS
Absolute Maximum Ratings
Parameter
Symbol
Conditions
Rating
Unit
Supply voltage range*1
Input voltage range*1 *2
Output voltage range*1 *2
Storage temperature range*3
VCC
VIN
VOUT
TSTG
VCC, VCC2 pins
XIN, OE pins
XOUT, OUT/OUTN pins
Chip form
−0.5 to +5.0
GND − 0.5 to VCC + 0.5
GND − 0.5 to VCC + 0.5
−65 to +150
V
V
V
°C
*1. This parameter rating is the values that must never exceed even for a moment. This product may suffer breakdown if this parameter rating is
exceeded. Operation and characteristics are guaranteed only when the product is operated at recommended operating conditions.
*2. VCC is a VCC value of recommended operating conditions.
*3. When stored in nitrogen or vacuum atmosphere applied to IC itself only (excluding packaging materials).
Recommended Operating Conditions
Parameter
Symbol
Conditions
Operating supply voltage
Operating supply voltage
difference
VCC
∆VCC
VCC, VCC2 pins
Voltage difference between VCC and
VCC2 pins
Input voltage
Operating temperature
Output load
Output frequency*1
VIN
TOPR
RL
fOUT
XIN, OE pins
Between OUT and OUTN pins
*1. Output frequency varies by version. Refer to “SERIES CONFIGURATION”.
Min
2.375
–0.1
GND
−40
99
80
Rating
Typ
–
–
–
+25
100
–
Max
3.6
+0.1
VCC
+85
101
600
Unit
V
V
V
°C
Ω
MHz
Note. Since it may influence the reliability if it is used out of range of recommended operating conditions, this product should be used within this range.
SEIKO NPC CORPORATION —5
5 Page 
5037 series
Please pay your attention to the following points at time of using the products shown in this document.
1. The products shown in this document (hereinafter “Products”) are designed and manufactured to the generally accepted standards of
reliability as expected for use in general electronic and electrical equipment, such as personal equipment, machine tools and
measurement equipment. The Products are not designed and manufactured to be used in any other special equipment requiring
extremely high level of reliability and safety, such as aerospace equipment, nuclear power control equipment, medical equipment,
transportation equipment, disaster prevention equipment, security equipment. The Products are not designed and manufactured to be
used for the apparatus that exerts harmful influence on the human lives due to the defects, failure or malfunction of the Products.
If you wish to use the Products in that apparatus, please contact our sales section in advance.
In the event that the Products are used in such apparatus without our prior approval, we assume no responsibility whatsoever for any
damages resulting from the use of that apparatus.
2. NPC reserves the right to change the specifications of the Products in order to improve the characteristics or reliability thereof.
3. The information described in this document is presented only as a guide for using the Products. No responsibility is assumed by us for
any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or
otherwise under any patents or other rights of the third parties. Then, we assume no responsibility whatsoever for any damages
resulting from that infringements.
4. The constant of each circuit shown in this document is described as an example, and it is not guaranteed about its value of the mass-
production products.
5. In the case of that the Products in this document falls under the foreign exchange and foreign trade control law or other applicable laws
and regulations, approval of the export to be based on those laws and regulations are necessary. Customers are requested
appropriately take steps to obtain required permissions or approvals form appropriate government agencies.
SEIKO NPC CORPORATION
1-9-9, Hatchobori, Chuo-ku,
Tokyo 104-0032, Japan
Telephone: +81-3-5541-6501
Facsimile: +81-3-5541-6510
http://www.npc.co.jp/
Email: sales@npc.co.jp
NC0309DE 2010.11
SEIKO NPC CORPORATION —11
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet 5037.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 5031SM | Zener Diode |  NTE Electronics |
| 5034B2C-DSD-E | 5mm Round LED 30deg |  Elecsound |
| 5034G1C-DSE-E | 5mm Round LED 30deg | Elecsound |
| 5034G3C-DSE-E | 5mm Round LED 30deg | Elecsound |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |